產品名稱：KUKA庫卡機器人更換平衡缸KR360-2C下探式倒掛式平衡杠

產品型號：KR360-2C

產品品牌：庫卡KUKA

產品類型：下探式倒掛式平衡缸

產品用途：KUKA KR360機器人

質保一年，可開專票

Product Name: KUKA Kuka Robot Replacement Balance Cylinder KR360-2C Downward Exploring Inverted Balance Bar
Product model: KR360-2C
Product brand: Kuka KUKA
Product type: downward probing inverted balance cylinder
Product Usage: KUKA KR360 Robot
One year warranty, with a special ticket available

KUKA機器人更換平衡缸

一、適用情況：

二、安全注意事項：

掛安全門鎖，掛維修警示牌，面板下電。

準備事項：

工具：內六角，卡簧鉗，套筒扳手，M12螺絲的拔銷器，軸承。

三、操作步驟：

1，將機器人開到零位，先取出插銷內的螺絲，在用卡簧鉗取出卡簧，后用拔銷器取出插銷，然后在取出飛碟圓盤。
2，對內部進行清潔
3，先拆三角架這側軸承，（注：三腳架下方有2顆M14的螺絲）。要取出側面的軸承先要拆掉罩殼和一個固定螺絲，使用木棍支撐，慢慢撬動，待到合適位置，用吊繩捆綁，最后取下平衡缸，在地上平穩放好。
4，拆除三角架里的軸承和對面軸承，并清洗干凈，有毛刺的地方用砂紙打磨光滑。然后更換新軸承和軸承卡簧。(注：安裝軸承時請上高溫潤滑脂)

5，將平衡缸用安全帶捆好抬到原來的位置，并裝上三角盤里的軸承，注意要對準螺絲孔的位置，安裝方法：先安裝后面2個軸承并固定，在安裝前面軸承和插銷，(注：安裝前面軸承時要用螺絲頂住平衡缸后面的彈簧板，將其往前頂，調整前方軸承方向和飛碟圓盤，到合適的位置裝入插銷)。

6，向該位置的圓盤打入4根螺絲，目的是使插銷那里的軸承對準位置

7，對準平衡缸的位置后，重新裝上插銷，裝上卡簧、罩殼后完成整個過程。

（注：完成后用油槍給軸承加高溫潤滑油.)

如果你有關于機器人任何配件的維修咨詢，請即時與湖南馳開智能機器人有限公司聯系吧。

KUKA Robot Replacing Balance Cylinder
1、 Applicable situation:
2、 Safety precautions:
Hang safety door locks, hang maintenance warning signs, and power down the panel.
Preparation:
Tools: hexagonal socket, circlip pliers, socket wrench, M12 screw extractor, bearing.
3、 Operating steps:
1. Drive the robot to the zero b, first remove the screw inside the pin, then use a snap ring pliers to remove the snap ring, then use a pin extractor to remove the pin, and then remove the flying disc.
2. Clean the interior
3. First remove the bearing on this side of the tripod (note: there are two M14 screws below the tripod). To remove the side bearing, first remove the cover and a fixed screw, use a wooden stick to support it, slowly pry it, wait until it reaches the appropriate b, bind it with a lifting rope, and finally remove the balance cylinder and place it smoothly on the ground.
4. Remove the bearings in the tripod and the opposite bearing, clean them thoroughly, and smooth any burrs with sandpaper. Then replace the bearings and bearing circlips with new ones. (Note: Please apply high-temperature lubricating grease when installing bearings)
5. Tie the balance cylinder with a safety belt and lift it to its original b. Install the bearings in the triangular disc, paying attention to aligning them with the screw holes. Installation b: first install the rear 2 bearings and fix them, and then install the front bearing and pin. (Note: When installing the front bearing, use screws to support the spring plate behind the balance cylinder, push it forward, adjust the direction of the front bearing and the flying disc, and install the pin in the appropriate b).
6. Drive 4 screws into the disc at this b to align the bearing at the pin with the b
7. After aligning the b of the balance cylinder, reinstall the latch, install the circlip, and complete the entire process.
(Note: After completion, use an oil gun to add high-temperature lubricating oil to the bearing.)

KUKA庫卡機器人更換平衡缸KR360-2C下探式倒掛式平衡杠

湖南馳開智能機器人有限公司提供工業機器人系統化服務，致力于投身工業機器人自動化行業十多年，噴涂機器人、點焊機器人、碼垛機器人，編程調試、維修保養、技術支持。誠信為本，嚴守標準！所售產品經過嚴格測試和認證。

我司有大量樣機測試平臺，可為客戶提供檢測。首先了解客戶設備故障，為客戶確認故障點，并提供解決方案及報價，客戶可選擇發至我司維修檢測或者技術工程師出差服務，維修產品測試正常后發貨。

我們將以的品質、的信譽、真誠積極的合作態度，與您建立一種互信、穩固、可靠、久遠的合作關系。為企業提供機器人問題系統解決方案！

歡迎查看主頁右上角咨詢我們——湖南馳開智能機器人有限公司

KUKA庫卡機器人更換平衡缸KR360-2C下探式倒掛式平衡杠

優勢品牌：ABB；發那科FANUC；安川YASKAWA；KUKA庫卡；川崎Kawasaki；西門子SIEMENS；橫河Yokogawa；德國鈷領guhring；FESTO費斯托；OMRON歐姆龍；Nabtesco納博特斯克

KUKA KUKA KR360-2HC2 FLR2H360 Gear Five 500KG Driving Wheel
KUKA KUKA 1FK7105-5AY81-1YY3-Z S18 00131491
KUKA KUKA KRC2 MGV PH803-2830 00-110-699
KUKA KUKA KSP 600-3 * 20 00198266
KUKA KUKA 10DCCG5B 00-177-96
KUKA KUKA KCP KRC2 00-107-264
KUKA Kuka Robot KRC4 Teaching pendant 00168334
KUKA KUKA MG_ 03_ 40_ 60 servo motor 00201179
KUKA KUKA ATX KRC4 power module DC Input 27V/11A
KUKA KUKA servo motor TSM3102N8032E207
KUKA KUKA servo motor TSM3204N8332E207
KUKA KUKA 00275478 servo motor ME_ 06_ 60_ thirty
KUKA KUKA 00120420 servo motor 1FK7034 5A791 1ZZ9 7
KUKA KUKA 00115927 Servo Motor 1FK7032-5AK71-1ZZ9-Z
KUKA Kuka Mg_ 20_ 84_ 45 servo motor 00200589
KUKA Kuka Mg_ 35_ 84_ 25 Motor 00-200-588
KUKA KUKA KSD1-08 E93DA22214B531
KUKA KUKA C4 Balancing Rod M1160 B1C Balancing Cylinder
KUKA harmonic reducer 32-160
Kuka KUKA reducer 2011K26189
KUKA KUKA KR360-2C downward probing balance cylinder
KUKA KUKA R460 GA16 balance cylinder C4 balance bar 189401
KUKA KUKA 622V 500-3 Robot
KUKA KUKA 500-3 Robot