澶╂触甯� 鍜屽钩鍗€(q奴) 鍖楄景鍗€(q奴) 娌冲寳鍗€(q奴) 娌宠タ鍗€(q奴) 瑗块潚鍗€(q奴) 娲ュ崡鍗€(q奴) 鏉遍簵鍗€(q奴) 姝︽竻鍗€(q奴) 瀵跺澔鍗€(q奴) 绱呮⿱鍗€(q奴) 澶ф腐鍗€(q奴) 婕㈡步鍗€(q奴) 闈滄捣绺� 瀵ф渤绺� 濉樻步鍗€(q奴) 钖婄福 鍗楅枊鍗€(q奴) 娌�?x霉n)|鍗€(q奴)
鑷烘 鎺涙 绛嗚鏈�鍏ㄨ嚜鍕�YO鍠�/闆欑窔鍦堣瑷傛瑾�(di脿o)瑭︼細
5.2.4瑾�(di脿o)鏁村ソ鑷烘 鎺涙 绛嗚鏈�鍏ㄨ嚜鍕�YO鍠�/闆欑窔鍦堣瑷傛鎻掗嚌浠ュ悗,鎶婄窔鏉愪竴绔姌褰庢垚閴ょ媭, 寤堕爢鏅傞嚌鏂瑰悜鍚戝彸鐠�(hu谩n)绻炶姱妫�,绌块亷姣忔牴鎻掗嚌,瑕嬪湒浜�.绌跨窔鍚�,鎸夆€濇墜鍕曠篂绶氣€濇寜閳�,浣跨窔鏉愮挵(hu谩n)绻炶姱妫掕綁(zhu菐n)鍕�,鎷夊嚭棣栨绶氬湀鍓帀(鍥犻枊濮嬫墜鍕曠┛绶氭檪鐨勫師鍥�,褰㈢媭涓嶈壇).
After the pins installed, pressed the wire with hook shape, turn clock wise with the wire goes through each pines as photo 2. After the wiring done press 鈥淢anual Wiring Button鈥� which turns around the mandrill running. Pull out the first sect and cut it out. (Because of wire shape no good when the first manual wiring).
5.3 鑷烘 鎺涙 绛嗚鏈�鍏ㄨ嚜鍕�YO鍠�/闆欑窔鍦堣瑷傛瑾�(di脿o)瑭﹂綊璺� Teeth pitch adjustment
榻掕窛鏄€氶亷浠ヤ笅涓夊€嬮浂浠跺浐瀹氱殑锛�1鎻掗嚌鏉�銆�2鎻掗嚌銆�3灏�(d菐o)绶氬
There are three parts supporting with the wire. 1. The pins. 2. The pin stands and 3. The teeth guide.
5.3.1灏�(d菐o)绶氬鏄悇绋綊璺濋€氱敤涓€鍊嬭(gu墨)鏍硷紝鍙爤閫氶亷瑾�(di脿o)鏁村皫(d菐o)绶氬鏃侀倞鐨勨€滈綊璺濊(di脿o)绡€(ji茅)铻虹挡鈥濆皣鍏跺乏鍙崇Щ鍕曚綅缃�銆俉ire running teeth guide is a kind of common specification. Just loosen the screws can move it to left or right b.
5.3.2绌垮ソ绶氫箣鍚庡厛鐢�鈥滄墜鍕曠篂绶氣€濈敓鐢�(ch菐n)涓€娈电窔鍦�,妾㈤榻掕窛鏄惁绗﹀悎瑕佹眰(鍙互鍦ㄦ鍣ㄤ笂鐨勫皫(d菐o)鍚戦綊璺濇涓婃椹�),濡傞綊璺濆亸澶�,鍓囨妸鈥滈綊璺濊(di脿o)绡€(ji茅)铻虹挡鈥濋爢鏅傞嚌鏃嬭綁(zhu菐n),鍙嶄箣浜﹀弽銆俇pon the wire setup done 鈥渕anual wiring鈥� trial suitable length of coil. In case double check each coil is qualified passed. (Can inspect onto the machine on the teeth pitch guide).If the teeth pitch bigger adjust screws turn clock wise. If teeth pitch smaller, turn against the direction.
5.4鑷烘 鎺涙 绛嗚鏈�鍏ㄨ嚜鍕�YO鍠�/闆欑窔鍦堣瑷傛瑾�(di脿o)瑭﹀垏鍒€ Cutter adjustment
5.4.1 鍏堣(di脿o)瑭﹀乏鍒囧垁,鍒€鍙ｇ殑闁嬪彛涓枔浣嶇疆灏嶆簴(zh菙n)闇€鍒囨柗鐨勭窔鍦堜綅缃�,鍒€鍙ｉ€插叆绶氬湀绱�1/3,瑕嬩笅鍦�.鐢ㄥ悓妯ｇ殑鏂规硶瑾�(di脿o)瑭﹀彸鍒囧垁 銆侫djust the left cutter; the centre of the cutter must face the wire cutting b. The cutter should be entered the coil 1/3 of depth. See photo 3. Use the same way for the right cutter for inspection.
