5.全自動臺歷 掛歷 筆記本單/雙線圈裝訂機自動繞線穿線系統的調整 Adjust the inserting system
機器出廠前已裝有調試好的一套模具。當機器需要更換模具時，可按照以下步驟進行。The machine is shipped with a good set of molds. When the machine needs to replace the mold, follow the steps below.
5.1 穿線 Inserting the wire
將線穿入進線組件，經過過線輪24.1，潤滑盒25，過線輪24.2,計數輪26（經過計數輪時將線繞計數輪一圈），過線輪24.3,再經過鐵線整直板(如圖一)，之后在芯棒上.
24.1 24.2 24.3 25 27 28
24.1-24.3 Wire running Wheels 25. Wire lubrication case.
26. Wire b device 27. Counter wheel. 28. Optic sensor.
Insert wire into the wire b device, through the wire running wheels 24.1, Wire lubrication case 25. Wire running wheels 24.2 and counter wheel 26. (Turn around the wheel, when goes through the counter wheel). Wire running wheel 24.3 Then goes through the hole of the straighten stand (as photo) then the wire goes into the mandrill.
5.2全自動臺歷 掛歷 筆記本單/雙線圈裝訂機調試芯棒 Mandrill adjustment
5.2.1要成形不同大小的線圈,須選用相應的線圈芯棒,選定適合的芯棒后,先將芯棒插入主軸并從主軸的另一端用螺絲鎖緊,開機運轉時,芯棒應與主軸同心.
Chose suitable mandrill according to different coil size. After install the mandrill onto the main axis with tighten screws, the mandrill should be the same concentric of the main axis when the machine is running.
5.2.2機上有三個插針板,作用是固定線圈的齒距.插針板須定在對應的插針板座上,從前方向下編號順序?yàn)?,2,3.
There are three pieces of pin stands. Order number 1,2,3 from the front to the lower one. Pins are fixed onto the stands for supporting the teeth pitch.
5.2.3把插針插入插針板上,注意針端與芯棒面須有0.05-0.15的間隙(工具箱配有塞尺).間隙過大,線材表面會刮花,如針端與芯棒配合過緊,則會刮花芯棒表面,造成坑槽,容易卡線和刮花線材.
When install the pins please keep the gap between 0.05-0.15mm (tool box has feeler gauge). Once the gap too big the wire material easy get scratched. The mandrill could be scratched the surface if the pins too closed. The mandrill the slot caused and could be damage the wire materials, too.
5.2.4全自動臺歷 掛歷 筆記本單/雙線圈裝訂機調整好插針以后,把線材一端折彎成鉤狀, 延順時針方向向右環繞芯棒,穿過每根插針,見圖二.穿線后,按”手動繞線”按鈕,使線材環繞芯棒轉動,拉出首段線圈剪掉(因開始手動穿線時的原因,形狀不良).
After the pins installed, pressed the wire with hook shape, turn clock wise with the wire goes through each pines as photo 2. After the wiring done press “Manual Wiring Button” which turns around the mandrill running. Pull out the first sect and cut it out. (Because of wire shape no good when the first manual wiring).
重慶市 江北區 渝北區 沙坪壩區 九龍坡區 萬州區 永川市 南岸區 酉陽縣 北碚區 涪陵區 秀山縣 巴南區 渝中區 石柱縣 忠縣 合川市 大渡口區 開縣 長壽區 榮昌縣 云陽縣 梁平縣 潼南縣 江津市 彭水縣 璧山縣 綦江縣 大足縣 黔江區 巫溪縣 巫山縣 墊江縣 豐都縣 武隆縣 萬盛區 銅梁縣 南川市 奉節縣 雙橋區 城口縣
全自動臺歷 掛歷 筆記本單/雙線圈裝訂機
