1.4，鎖線裝訂設備 臺歷自動鎖線機參數
1.4 Parameters
規格：3400x880x1300（mm）
Size: 3400x880x1300（mm）
電源：AC380V 3+2
Power: AC380V 3+2
功率：2.0KW
重量：凈重700KG
Weight:
1.5，鎖線裝訂設備 臺歷自動鎖線機尺寸
120mm---400mm寬幅，長度100mm-800mm，書本厚度3mm-30mm
第二節：
鎖線裝訂設備 臺歷自動鎖線機生產程序描述
2. Debion of the production process
2.1，開機前準備
2.1 Prepare before
2.1.1安裝機器
2.1.1 Install the machine
機器開箱到生產場地后，前段送料系統和后段收料臺是折疊狀態，需要人工往上放平后方可開機準備，具體操作需兩側螺絲拆開放平后再找到對應的螺絲孔上好螺絲固定，屏幕方向4顆M8內六角螺絲，對面2顆M8螺絲，如圖
After the machine is out of the box to the production site, the front feeding system and the rear receiving station are in the folded state, and need to be manually laid up to be ready for powering. After the flat screws on both sides are removed, the corresponding screw holes are found. Screws, the direction of the screen 4 M8 hexagonal screws, the opposite 2 M8 screws, as shown
1.2 手動開機狀態下調整好機器的書本檔邊位置，使之與機架邊緣平行，另一擋位在人工放料使用下可以適當放開距離或者拆開不用。
2.2 Manual boot state machine books to adjust the edge of the b, so that the edge of the rack parallel to the other gear in the artificial discharge can be used to release the appropriate distance or split open.
1.3
適當調整上下輸送鏈條的壓緊力度（手拉書本不動為宜），在觸摸屏界面設置調好主機運行速度，先期調節到10-20頻率為好（如圖），根據熟練程度再增加或減少。
2.3 The appropriate adjustment of the upper and lower conveying chain of the compression force (hand-pulled books do not move), set the touch screen interface to adjust the host speed,
調整好書本來料監測電眼時間，一般為2-3秒為宜（正常生產）
Adjust the book material incoming electric eye time, generally 2-3 seconds is appropriate (normal production)
2.3，手動開機狀態利用手持點動開關按鈕慢慢輸送書本，調整書本厚度壓條使之平行于下支撐板，無需太緊，書本能自由走動為佳（如下圖）。
2.3 Manual power-on state Use the hand-held jog switch button to slowly transfer the book, adjust the thickness of the book to make it parallel to the lower support plate, without too tight, the book can move freely better (see below).鎖線裝訂設備 臺歷自動鎖線機
回位彈簧力量大小適當調節合適的力度（如下圖）
The size of the return spring force appropriate to adjust the appropriate force (see below)
2.4，適當調節送料皮帶無極調速器 書本間距位置，根據開機速度和產品的需求適當調整間距，一般為2CM左右為宜。
2.4 Adjust the feed belt stepless adjuster spacing, according to the boot speed and product needs to adjust the spacing, generally about 2CM is appropriate.
鎖線裝訂設備 臺歷自動鎖線機
山東省
濟南市 青島市 臨沂市 濟寧市 菏澤市 煙臺市 泰安市 淄博市 濰坊市 日照市 威海市 濱州市 東營市 聊城市 德州市 萊蕪市 棗莊市
