書刊裝訂設備的操作及更換零部件折卸方法 Testing and running
1．安全操作注意事項 Notice of safety operate
1.2 了解機器各部分的作用和潛在危險區域，知道必要的安全措施。
Understand the role of the various parts of the machine and potentially dangerous areas, and know the necessary safety measures
1.3 啟動機器前，檢查機器各手柄，按鈕是否處于預定的工作位置。
Before starting the machine, check the handle of the machine and whether the button is in the intended working b.
1.4 如果書刊裝訂設備作時突然停止，不要馬上重新啟動，應該按下“總?！弊枣i按鈕，檢查停機原因，待故障排除后方可重新啟動。 If the machine suddenly stops working, do not restart immediaby, you should press the "total stop" self-locking button, check the cause of the shutdown, to be troubleshooting before you can restart.
1.5 不允許在書刊裝訂設備運轉時，維護運動零部件和靠近運動零部件的其他零部件。 It is not permissible to maintain moving parts and other parts near moving parts while the machine is running.
1.6 大面積保養或修理時，必須按下“停止”自鎖按鈕，切斷所以電源、氣源。Large area maintenance or repair, you must press the "stop" self-locking button, cut off the power supply, gas source.
1.7 書刊裝訂設備在進行調整、保養和修理工作時，不得使用不適當?shù)墓ぞ摺９ぷ魍戤吅蟊仨毲謇頇z查機器上的工具和其他雜物，以免發生故障。 Undue tools should not be used for adjustment, maintenance and repair work. After the work must be cleaned to check the tools and other debris on the machine, so as to avoid failure.
1.8 在重新啟動機器前，應檢查所有安全設施是否處在正常位置，是否緊定，注意機器周圍的其他人員是否處在安全的位置。 Before restarting the machine, check that all safety devices are in their normal b, are they tightened, and that the rest of the machine is in a safe place.
1.9 保持書刊裝訂設備和周圍環境的清潔，及時清除掉落在地板上的油污，清理工作區的工具、抹布及碎紙廢料等。 Keep the machine and the surrounding environment clean, remove the oil on the floor in a timely manner, clean up the work area of the tools, rags and shredded scrap.
1.10 及時維護、更換已失效和損壞的裝置，及時報告機器發生的問題。Timely maintenance, replacement of failure and damage to the device, the timely report of the machine problems.
書刊裝訂設備收放物料裝置的調整 Adjust the feed and receive belt
2.1 上料裝置的調整 Adjust the feed belt
該工位可根據產品的寬窄來調節輸送料道的寬度，松開護罩1的固定螺絲123，然后根據產品的需要調整料道的寬窄。The b of the station can be adjusted according to the b of the product to adjust the b of the conveyor material, refer to (Picture 9) to release the cover screw 1 123, and then adjust the b of the material according to the needs of the material.
2.2書刊裝訂設備收料裝置的調整 Adjust the receive belt
該工位主要是配合主機完成收料工作，可根據主機的裝訂速度自動調整線體的每次位移. The station is mainly with the host to complete the receipt work, according to the host's binding speed automatically adjust the line of each displacement.
3. 書刊裝訂設備推刀調試 Test push knife
根據產品大小的需要，可通過調節推刀組的固定螺絲的安裝位置來調節T的寬度（見圖十）Depending on the size of the product, the b of the T can be adjusted by adjusting the mounting b of the setscrews' fixing screws (Picture 10)
4.書刊裝訂設備機器手送料系統的調整 Adjust the feed system
北京市 廣東省 山東省 江蘇省 河南省 上海市 河北省 浙江省 香港特別行政區 陜西省 湖南省 重慶市 福建省 天津市 云南省 四川省 廣西壯族自治區 安徽省 海南省 江西省 湖北省 山西省 遼寧省 臺灣省 黑龍江 內蒙古自治區 澳門特別行政區 貴州省 甘肅省 青海省 新疆維吾爾自治區 西藏區 吉林省 寧夏回族自治區
