| Functional safety related beters | ||
|---|---|---|
| MTTFd | 110 a | |
| Mission Time (TM) | 20 a | |
| L10h | 1.9 E+11 at 6000 rpm and 20/40 N axial/radial shaft load | |
| Diagnostic Coverage (DC) | 0 % | |
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC | |
| No-load supply current | max. 140 mA | |
| Power consumption | ≤ 2.5 W , without output drivers | |
| Linearity | ± 0.5 LSB | |
| Output code | Gray code, binary code | |
| Code course (counting direction) | cw ascending (clockwise rotation, code course ascending) | |
| Code preparation time | 0.3 ms | |
| Interface | ||
| Interface type | Push-pull, parallel , short-circuit protected | |
| Resolution | ||
| Multiturn | 25 Bit | |
| Load current | 20 mA | |
| Voltage drop | ≤ 2.5 V | |
| Signal voltage | ||
| High | operating voltage minus voltage drop | |
| Low | ≤ 2.8 V | |
| Rise time | 300 ns | |
| De-energized delay | 300 ns | |
| Code change frequency | 400 kHz | |
| Input 1 | ||
| Input type | Selection of counting direction (cw/ccw) | |
| Signal voltage | ||
| High | 10 ... 30 V | |
| Low | 0 ... 2 V | |
| Input current | < 6 mA | |
| Input 2 | ||
| Input type | Temporary storage (LATCH) | |
| Signal voltage | ||
| High | 10 ... 30 V | |
| Low | 0 ... 2 V | |
| Input current | < 6 mA | |
| Switch-on delay | < 0.1 ms | |
| Switch-off delay | < 0.1 ms | |
| Input 3 | ||
| Input type | zero-set (PRESET) | |
| Signal voltage | ||
| High | 10 ... 30 V | |
| Low | 0 ... 2 V | |
| Input current | < 6 mA | |
| Switch-on delay | < 1 ms | |
| Connection | ||
| Connector | type 9426, 26-pin | |
| Cable | ?9 mm, 15 x 2 x 0.14 mm2, 2 m | |
| Standard conbity | ||
| Degree of protection | DIN EN 60529, IP65 | |
| Climatic testing | DIN EN 60068-2-3, no moisture condensation | |
| Emitted interference | EN 61000-6-4:2007 | |
| Noise immunity | EN 61000-6-2:2005 | |
| Shock resistance | DIN EN 60068-2-27, 100 g, 6 ms | |
| Vibration resistance | DIN EN 60068-2-6, 10 g, 10 ... 2000 Hz | |
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose, Class 2 Power Source | |
| Ambient conditions | ||
| Operating temperature |
-40 ... 85 °C (-40 ... 185 °F) cable models: -30 ... 70 °C (rigid wiring) -5 ... 70 °C (flexible wiring) |
|
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) (cable models: -5 ... 70 °C) | |
| Mechanical specifications | ||
| Material | ||
| Combination 1 |
housing: powder coated aluminum flange: aluminum shaft: stainless steel |
|
| Combination 2 (Inox) |
housing: stainless steel flange: stainless steel shaft: stainless steel |
|
| Mass |
approx. 400 g (combination 1) approx. 800 g (combination 2) |
|
| Rotational speed | max. 12000 min -1 | |
| Moment of inertia | 30 gcm2 | |
| Starting torque | ≤ 5 Ncm | |
