產品（礦用風動/氣動切割鋸）介紹： 
1.該鋸適用于危險的工作環境，可在較高溫的環境下作業，無火花，在潮濕的環境中無漏電危險，是一款性能可靠、安全型及效率極高的理想風動工具之一。廣泛用于采礦、石化、建筑等行業。 
2.利用井下壓風管道系統作為動力源。重量輕，易攜帶；結構科學，便于作業。 
3.可快速切割管道、電纜、角鋼、結構鋼、U型鋼、鏈條、錨桿、錨索等。 
4.錮金屬鋼合金超級鋸條，耐高溫、耐摩擦、使用壽命長。非常適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。
 
技術參數：
型號  FDJ-230 
功率  2kw 
耗氣量  0.8
切割寬度（直徑）  230mm 
鋸片速度  60m/min

重量  8kg 

使用方法：
  1、了解所需切割的材料。
  2、確保牢固固定了所需切割的材料，防止其移動。
  3、電源接上時，用手指按壓閥桿，然后開始切割。
  4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
  5、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。
  6、更換鋸片前，務必?cái)嚅_(kāi)氣動力。
  7、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
為了安全作業需要注意以下幾點：
   1、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命
  2、關閉氣源時，釋放閥桿。
  3、更換鋸片前，務必?cái)?span>氣動源。
  4、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
  5、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。
  6、了解所需切割的材料。
  7、確保牢固固定了所需切割的材料，防止其移動。
  8、接好氣時，用手指按壓閥桿，然后開始切割。
特點：
1.輕便型現場移動活躍作業，瓦斯管，自來水管，電器，機械車間，建設，煤礦及其他切斷作業現場。
2.臺灣攜帶式小型鋸床，無需冷卻液，自然干切。
3.切割材料范圍廣，在規定硬度范圍內的金屬、非金屬都能切割。
4.精加工，切割面平整，大大提高工作過效率。 5.切割角度可調整，0到90度。

聯系人金志鵬電話13934240041
Usage b：
1, what's needed to cut materials.
2, to ensure that the firmly required cutting material, to prevent the mobile.
3, connected with the power on, press with your fingers and began cutting stem.
4, saw the weight to control the cutting pressure. For soft materials, the weight is enough. Too much pressure will reduce the speed of the saw blade. For hard materials, to reduce the rotational speed of the saw blade by pressurized b. Keep straight cutting saw. Any distortion or skewed blade may reduce its service life. (Note: avoid cutting debris may fall. Cutting is finished, do not make contact with other staff saw your body, the workpiece or nearby).
5, before the start of the next cut, the blade must keep moving. Pneumatic saw, saw blade can not touch any surface.
6, replacing the saw blade, be sure to disconnect the gas power.
7, clockwise adjust the handle to release the tension on the saw blade guide rod. Then release the lock side panel to open the side panel. And then removed from the drive wheel and the blade from the saw belt guide rod release.



In order to safety work should pay attention to the following points:
1, saw the weight to control the cutting pressure. For soft materials, the weight is enough. Too much pressure will reduce the speed of the saw blade. For hard materials, to reduce the rotational speed of the saw blade by pressurized b. Keep straight cutting saw. Any distortion or skewed blade may reduce its service life
2, closed source, release valve.
3, replacing the saw blade, must die moving source.
4, clockwise adjust the handle to release the tension on the saw blade guide rod. Then release the lock side panel to open the side panel. And then removed from the drive wheel and the blade from the saw belt guide rod release.
5, before the start of the next cut, the blade must keep moving. Pneumatic saw, saw blade can not touch any surface.
6, what's needed to cut materials.
7, to ensure that the firmly required cutting material, to prevent the mobile.
8, aerobic, pressing with a finger and began cutting stem.
Characteristic：
1. portable mobile active site operation, gas pipe, tap water pipe, electric appliance, mechanical workshop, construction, coal and other cutting operation site.
2. Taiwan small portable machine, without cooling liquid, natural dry cutting.
3. cutting a wide range of materials, within the specified range of hardness of bls and non bls can be cut.
4. finish, smooth cutting surface, greatly improve work efficiency. 5. the cutting angle can be adjusted to 0 to 90 degrees.