NI-ROD? 44焊絲
NI-ROD 44焊絲適于高速焊接，可形成優質焊縫。這種焊絲還適合于機器人焊接或任何自動或半自動焊接，并可用于全位置焊。這種焊絲具有優良的抗?jié)窨沽研阅?，可用于球墨鑄鐵的焊接，因此可以用成本較低的球墨鑄鐵工件代替鋼質鑄件或鍛件。
NI-ROD 44焊絲是一種實心鎳－鐵－錳焊絲，可在任何位置下對球墨鑄鐵、可鍛鑄鐵或灰口鑄鐵進行自動或半自動焊接。在機器人的焊接中，熔覆率可達每分鐘18 磅（8kg），焊絲熔化速度可達每分鐘50英寸（1270mm）。若用于埋弧焊接應采用INCOFLUX 7埋弧焊劑。
用這種焊絲進行焊接，一般不需要焊前預熱或焊后熱處理，但對于那些塑性較低，約束嚴重的大型鑄件，進行這種處理可能較好。
|
規格 AWS A5.15 ENiFeMn-Cl ISO E C NiFeMn-CI UNS W72006 Europe E C NiFeMn-CI
|
|
化學 Ni------------44 Mn ------------ 11 成份 C ---------- 1.5 Fe ------------ 45
|
|
最低 拉伸強度，psi 100,000 機械 MPa 690 性能 延伸率，(4d）% 35
|
焊絲可以以線卷或直線狀供貨，并有幾種不同直徑以供選擇，如下表所示：
產品
|
mm |
0.8 |
0.9 |
1.0 |
1.14 |
1.2 |
1.6 |
2.4 |
3.2 |
|
in |
0.030 |
0.035 |
0.040 |
0.045 |
0.047 |
0.062 |
0.093 |
0.125 |
供貨
狀態
直線長度--915 mm(36”)或1000 mm(39”)
NI-ROD 44 wire is suitable for high speed welding, which can b high quality weld. This wire is also suitable for robot welding or any automatic or semi-automatic welding, and can be soldered at full b. This kind of wire has excellent anti-moisture resistance and can be used in the welding of nodular cast iron, so it can replace steel castings or forgings with lower cost ductile iron workpieces.
NI-ROD 44 welding wire is a kind of solid NI- iron - manganese welding wire, which can be automatically or semi-automatic welding of nodular cast iron, malleable cast iron or gray cast iron at any b. In robot welding, the penetration rate can reach up to 18 pounds (8kg) per minute, and the melt speed can reach 50 inches per minute (1270mm). If used for submerged arc welding, INCOFLUX 7 submerged arc welding agent is adopted.
This kind of welding wire is used for welding, which generally does not require pre-heating or post-weld heat treatment, but for those large castings that are less plastic and have severe constraints, such treatment may be better.
Specification of AWS A5.15 enifemn-cl ISO E C nifemn-ci
UNS W72006 Europe E C nifemn-ci
Chemical Ni -- -- -- -- -- -- -- -- -- -- -- -- 44 Mn -- -- -- -- -- -- -- -- -- -- -- -- 11
Ingredients C -- -- -- -- -- -- -- -- -- -- 1.5 Fe -- -- -- -- -- -- -- -- -- -- -- -- 45
Minimum tensile strength, psi 100,000
Mechanical 690 MPa
Perbance elongation, (4d) % 35
The wire can be supplied in a reel or straight line, with several different diameters for selection, as shown in the following table:
products
Mm 0.8 0.9 1.0 1.14 1.2 2.4 3.2
In 0.030 0.035 0.040 0.045 0.035 0.062 0.093 0.125
supply
state
The linear length -915 mm (36) or 1000 mm (39))
