WWW国产精品内射老熟女,亚洲无码成人综合网,AV美女主播高潮,无码图片二区

商品介紹：

·FDJ-120型風動切開鋸適用于風險的作業環境，可在較高溫的環境下作業，無火花，在濕潤的環境中無漏電風險，是一款功能牢靠、安全型及效率極高的抱負風動東西之一。廣泛用于采礦、石化、修建等職業。

·使用井下壓風管道體系作為動力源。重量輕，易帶著；構造科學，便于作業。

·可迅速切開管道、電纜、角鋼、構造鋼、U型鋼、鏈條、錨桿、錨索等。

·錮金屬鋼合金超級鋸條，耐高溫、耐沖突、運用壽數長。十分適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。

 技術參數：

使用方法：
  1、了解所需切割的材料。
  2、確保牢固固定了所需切割的材料，防止其移動。
  3、電源接上時，用手指按壓閥桿，然后開始切割。
  4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
  5、下次切割開始前，鋸片必須保持運動狀態。電動鋸時，鋸片不能接觸任何表面。
  6、更換鋸片前，務必斷開電源力。
  7、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
為了安全作業需要注意以下幾點：
   1、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命
  2、關閉電源時，釋放閥桿。
  3、更換鋸片前，務必斷開電源。
  4、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
  5、下次切割開始前，鋸片必須保持運動狀態。電動鋸時，鋸片不能接觸任何表面。
  6、了解所需切割的材料。
  7、確保牢固固定了所需切割的材料，防止其移動。
  8、接電源時，用手指按壓閥桿，然后開始切割。
  9、斷開電源時，關閉電源軟管閥。斷開前，先打開電源閥給軟管減壓

聯系人金經理電話13934240041
山西萬澤錦達質量過硬做的就是口碑沒毛病歡迎各位老鐵致電咨詢

Introduction of pneumatic hand held cutting saw
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose. Yuanhui District FDJ-120/ portable cutting saw
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. We don't promise unrealistic theories to customers, bragging, and exaggerating. But it can always be on the path of innovation, because the market gives us the answer, and the customer has given us approval.