外貼式橡膠止水帶EB型
中埋式橡膠止水帶必須采取可靠的固定措施，避免在澆注混凝土?xí)r發生位移，保證止水帶在混凝土中的正確位置。對于固定橡膠止水帶時，只能在止水帶的允許部位上穿孔打洞，不得損壞本體部分。對于止水帶的固定方法應按設計要求的施工規范進行，常用的固定方法有：利用附加鋼筋固定；專用卡具固定；用鉛絲和模板固定
The bded rubber water stop must take reliable measures to avoid displacement when pouring concrete, and ensure the correct b of the water stop belt in the concrete. When the rubber sealing belt is fixed, the perforated hole can only be perforated on the allowed part of the water stop belt, and the part of the body can not be damaged. For the fixed b of waterstop shall be in accordance with the design requirements of the construction specifications, fixation bs are commonly used: the use of additional reinforcement fixation; special fixture fixation; fixation with wire and template
等。不論采用何種固定方法，都必須保證止水帶定位準確，不損壞止水帶有效部分，方便混凝土澆搗。
Etc.. No matter what fixed b used, it is necessary to ensure the accurate bing of the water stop belt, not damage the effective part of the water check belt, convenient concrete pouring.
應盡量在工廠中連接成整體。如因制造工藝、運輸條件等限制，需在現場連接的，應采用熱壓硫化膠合（橡膠止水帶）或焊接（塑料止水帶），其接頭外觀應平整光潔，抗拉強度不低于母材的80%。 不加任何處理的所謂“搭接”。橡膠止水帶的各種交叉連結點，要使用我們成林公司生產成配件，以保證在施工中現場連接只在直線段進行。足夠的變形能力，與混凝土具有良好粘接性能的柔性材料。
外貼式橡膠止水帶EB型
It should be connected to the whole as far as possible in the factory. If the manufacturing process and transportation conditions are limited, hot pressing vulcanizing (rubber water stop) or welding (plastic water stop) shall be applied to the field connection. The appearance of its joints should be smooth and smooth, and the tensile strength is no less than 80% of the base bl. The so-called "lap joint" without any treatment. The rubber sealing belt of various cross junction, to use our company into the forest production parts, to ensure the construction site in the connection only in a straight line segment. Sufficient debation capacity, flexible material with good adhesion to concrete.
在橡膠止水帶施工過程中，由于混凝土中有許多尖角的石子和銳刃的鋼筋，所以在澆搗和定位止水帶時，應注意澆搗的沖擊力，以免由于力量過大而刺破橡膠止水帶。如發現有破裂現象應及時修補，否則在接縫變形和受水壓時，橡膠止水帶所能抵抗外力的能力就會大幅度降低。 在定位橡膠止水帶時，一定要使其在界面部位保持平展，更不能讓止水帶翻滾、扭結如發現有扭轉不展現象應及時進行調正。在澆鑄固定止水帶時，應防止水帶偏移，以免單側縮短，影響止水效果。在混凝土澆搗時還必須充分震蕩，以免止水帶和混凝土結合不良而影響止水效果。止水帶接頭必須粘接良好，如施工現場條件具備，可采用熱硫化連接的方法 。
外貼式橡膠止水帶EB型
In the construction process of rubber sealing belt, because there are many sharp stones and sharp edged steel bars in concrete, when pouring and locating the sealing belt, we should pay attention to the impact force of pouring and tamping, so as not to pierce the rubber water stop because of too much power. If it is found that the rupture phenomenon should be repaired in time, otherwise the ability of rubber sealing belt to resist external force will be greatly reduced when the joint debation and water pressure are subjected to water pressure. When bing the rubber water stop, it must be kept flat at the interface, and even let the water stop roll and twist. If it is found that there is a twist and it does not appear, it should be adjusted in time. When casting fixed water stop belt, water belt shift should be prevented so as to avoid single side shortening and influence the effect of water stop. When the concrete is poured, it must also be fully concussion, so as to avoid the bad combination of water and concrete, which will affect the effect of water stop. The joint of the water stop belt must be well bonded, such as the condition of the construction site, and the b of hot vulcanization can be used.
河北瑞博橡塑制品有限公司是一家集橡膠支座，橡膠止水帶，伸縮縫等工程橡膠制品為主的專業生產企業。歡迎各界朋友蒞臨參觀指導，業務洽談。歡迎致電：13166570832