使用方法：     1、了解所需切割的材料。     2、確保牢固固定了所需切割的材料，防止其移動。     3、電源接上時，用手指按壓閥桿，然后開始切割。     4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）     5、下次切割開始前，鋸片必須保持運動狀態。電動鋸時，鋸片不能接觸任何表面。     6、更換鋸片前，務必?cái)嚅_電源力。     7、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
聯系人金經理電話：13934240041

為了安全作業需要注意以下幾點：    1、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命   2、關閉電源時，釋放閥桿。     3、更換鋸片前，務必?cái)嚅_電源。     4、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。     5、下次切割開始前，鋸片必須保持運動狀態。電動鋸時，鋸片不能接觸任何表面。     6、了解所需切割的材料。     7、確保牢固固定了所需切割的材料，防止其移動。     8、接電源時，用手指按壓閥桿，然后開始切割。     9、斷開電源時，關閉電源軟管閥。斷開前，先打開電源閥給軟管減壓。

In order to safe operations need to pay attention to the following points: 1, saw the weight to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any distortion or skewed blade may reduce the service life of 2, turn off the power when the release valve. 3, replacing the saw blade before, be sure to disconnect the power supply. 4, clockwise adjust the handle to release the tension on the saw blade guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. 5, before the start of the next cut, the blade must keep moving. When an electric saw is used, a saw can not contact any surface. 6, what's needed to cut materials. 7, to ensure that the firmly required cutting material, to prevent the mobile. 8, when connecting the power press with your fingers and began cutting stem. 9, disconnect the power supply when the power off valve hose. Before disconnecting, open the power valve and decompress the hose.。