d150*21板式橡膠支座
建筑伸縮縫即伸縮縫，是指為防止建筑物構件由于氣候溫度變化（熱脹、冷縮），使結構產生裂縫或破壞而沿建筑物或者構筑物施工縫方向的適當部位設置的一條構造縫。伸縮縫是將基礎以上的建筑構件如墻體、樓板、屋頂（木屋頂除外）等分成兩個獨立部分，使建筑物或構筑物沿長方向可做水平伸縮。
Expansion joints, namely expansion joints, refer to a structural joint to prevent structural components from cracking or damaging due to climatic and temperature changes, such as thermal expansion and cold shrinkage, along the proper direction of construction joints of buildings or structures. Expansion joints are divided into two independent parts, such as walls, floors, roofs (except wooden roofs), so that buildings or structures can be horizontally bescoped along long directions.
防止房屋因氣候變化而產生裂縫。其做法為：沿建筑物長度方向每隔一定距離預留縫隙，將建筑物從屋頂、墻體、樓層等地面以上構件全部斷開，建筑物基礎因其埋在地下受溫度變化影響小，不必斷開。伸縮縫的寬度一般為20厘米到30厘米，縫內填保溫材料，兩條伸縮縫的間距在建筑結構規范中有明確規定。
d150*21板式橡膠支座
Prevent cracks in the house from climate change. The b is to reserve gaps in every distance from the length of buildings, and to disconnect buildings from above ground components, such as roofs, walls, floors, etc., because the foundation of buildings is less affected by temperature changes due to their underground burying, so they do not need to be disconnected. The b of the expansion joint is usually 20 cm to 30 cm. The insulation materials are filled in the seams, and the distance between the two expansion joints is bly defined in the construction code.
若建筑物平面尺寸過長，因熱脹冷縮的緣故，可能導致在結構中產生過大的溫度應力，需在結構一定長度位置設縫將建筑分成幾部分，該縫即為溫度縫。對不同的結構體系，伸縮縫間的距離不同，中國現行規范《混凝土結構設計規范》GB50010-2010中8.1條對此有專門規定。
If the plane size of a building is too long, it may cause excessive temperature stress in the structure due to thermal expansion and cold contrb. It is necessary to sew the building into several parts at a certain length, and the joints are temperature joints. For different structural systems, the distance between expansion joints is different. The 8.1 rule in the code for design of concrete structures in China is GB50010-2010.
橋梁伸縮縫GQF-C型、GQF-Z型、GQF-E型、GQF-F型、GQF-MZL型,全都是采用熱軋整體成型的異型鋼材設計的橋梁伸縮縫產品。其中GQF-C型、GQF-Z型、GQF-L型、GQF-F型橋梁伸縮裝置適用于伸縮量80mm以下的的橋梁, GQF-MZL型橋梁伸縮裝置型是由邊梁、中梁、橫梁和連動機構組成的模數式橋梁伸縮縫裝置,適用于伸縮量80mm-1200mm的大中跨度橋梁。
Bridge expansion joints GQF-C, GQF-Z, GQF-E, GQF-F and GQF-MZL are all welded expansion joint products designed by hot rolled integral shaped steel. The GQF-C type, GQF-Z type, GQF-L type, GQF-F type bridge expansion device is suitable for the expansion of the 80mm below the bridge, GQF-MZL bridge expansion device is composed of modular bridge expansion edge beam, beam, beam and bage mechanism joint device, suitable for large and medium span bridge expansion 80mm-1200mm.
為滿足橋面變形的要求，通常在兩梁端之間、梁端與橋臺之間或橋。
In order to meet the requirements of the debation of the bridge, it is usually between the two beam ends, between the Liang Duan and the abutment or the bridge.
d150*21板式橡膠支座
橡膠墊塊是由多層橡膠片硫化粘合而成一種普通橡膠支座產品,這種產品具有足夠的豎向剛度,能夠?qū)⒅ё喜繕?gòu)造的反力可靠的傳遞給墩臺,支座具有良好的彈性,以應對橋梁的梁端的轉動;又有較大的剪切變形能力，以滿足上部構造的水平位移。
The rubber pad is composed of multilayer rubber vulcanization bonding a common rubber bearing products, this product has enough vertical stiffness, can force reliable transfer to the pier upper bearing structure, bearing has good flexibility, rotating beam end in response to the bridge; and a larger shear debation capacity in order to meet, the horizontal displacement of superstructure.
橡膠墊塊的布置
The arrangement of rubber b blocks
橡膠墊塊的布置主要和橋梁的結構形式有關。通常在布置支座時需要考慮以下的基本原則:
The layout of the rubber pad is mainly related to the structural b of the bridge. The following basic principles should usually be taken into consideration in the arrangement of support:
(1)上部結構是空間結構時，橡膠墊塊應能同時適應橋梁順橋向(X方向)和橫橋向(Y方向)的變形;
(1) when the superstructure is a spatial structure, the rubber pad should be able to adapt to the debation of the bridge direction (X direction) and the transverse bridge (Y direction).
(2)橡膠墊塊必須能可靠的傳遞垂直和水平反力;
