橡膠止水帶系列
Rubber hose series
一、橡膠止水帶性能特點
Perbance characteristics of rubber water stop belt
橡膠止水帶廣泛應用于各種類型的混凝土結構中，例如：擋水壩、蓄水池、地鐵、涵洞、隧道等地下工程中。在這些工程中，由于不能連續澆鑄，或由于地基的變形，或由于溫度變化引起的混凝土構件的熱脹冷縮等原因，在澆鑄時常留有變形縫、施工縫，這些縫的防滲漏問題就要采用在變形縫的部位澆鑄橡膠止水帶的方法來解決，它既能防止地下水或外界水滲漏到建筑物結構中，橡膠止水帶又可防止建筑內的水漏到外界。
Rubber water sealing belts are widely used in various types of concrete structures, such as dam, reservoir, subway, culvert, tunnel and other underground works. In these projects, due to the continuous casting, or as a result of the ground debation, or caused by temperature change of concrete thermal expansion and contrb, often left in the casting debation joints, construction joints, these joints leakage problems must be adopted in the b of debation of the casting parts of the rubber sealing belt to solve and it can prevent the water leakage of groundwater or external to the building structure, the rubber sealing strip can prevent water leakage to the outside the building.
二、橡膠止水帶技術標準
Two. Technical standard for rubber sealing belt
1. 我公司生產的橡膠止水帶是采用國家標準GB18173.2-2000標準組織生產的，尺寸公差一律按國家標準執行，如用戶有特殊要求，可按用戶要求制造。
1., the rubber sealing belt produced by our company is organized by the national standard GB18173.2-2000 standard. The size tolerance is all carried out according to the national standard. If the user has special requirements, it can be manufactured according to user requirements.
2. 橡膠止水帶型號以分類別分類編號，以方便設計參考和用戶定貨。
2. the type of rubber water stop belt is classified and numbered by classification to facilitate the design of reference and user order.
3.我公司可按用戶要求生產各種形狀、尺寸的橡膠止水帶，另外還可為不同工程、不同部位的需要備有十字型、丁字型、斜度型和內外轉角型產品，可適用于任何設計要求。
3., our company can produce various shapes and sizes of rubber water stop as required by users. Besides, it can also be cross shaped, T-shaped, inclined and inside and outside corner products for different engineering and different parts. It can be applied to any design requirement.
4.橡膠止水帶在運輸時，應要避免陽光直射，勿與熱源、油類及有害溶劑接觸。成品應取直平放，勿加重壓。存放場所最好保持-10-+30，相對濕度40%-80%。
4. rubber sealing strip during transportation, should avoid direct sunlight, do not contact with heat, oil and harmful solvent. The finished product should be put straight, without heavy pressure. The best storage place is -10-+30, and the relative humidity is 40%-80%.
三、橡膠止水帶施工方法：
Three. The construction b of rubber water stop belt:
橡膠止水帶是在混凝土澆鑄過程中部分或全部澆埋進混凝土中。
The rubber water stop belt is partially or compleby buried into the concrete in the process of concrete casting.
橡膠止水帶在澆埋混凝土以前先要使其在界面部位保持平展，接頭部位粘接緊固，再以適當?shù)牧Τ浞譂矒v、震蕩混凝土來定位橡膠止水帶，使其與混凝土良好的結合，以免影響止水效果。
The rubber sealing belt should be kept at the interface part before pouring the concrete, and the joints should be fastened and fastened. Then the rubber sealing belt will be bed with the appropriate force and the concrete will be shocked to make it integrate well with the concrete so as not to affect the sealing effect.
四、橡膠止水帶施工注意事項：
Four, rubber water stop belt construction attention:
1、止水帶在施工過程中，由于混凝土中有許多尖角的石子和銳刃的鋼筋，所以在澆搗和定位橡膠止水帶時，應注意澆搗的沖擊力，以免由于力量過大而刺破橡膠止水帶。如有發現有破裂現象應及時修補，否則在接縫變形和受水壓時，橡膠止水帶所能抵抗外力的能力就會大幅度將會大幅度降低。
1, during the construction process, because there are many sharp stones and sharp steel bars in the concrete, when pouring and locating rubber water stop, we should pay attention to the impact force of pouring, so as not to pierce the rubber water stop because of too much power. If rupture is found, it should be repaired in time. Otherwise, when the joint is debed and subjected to water pressure, the ability of rubber sealing belt to resist external force will be greatly reduced.
2、在地位橡膠止水帶時，一定要使其在界面部位保持平展，更不能讓橡膠止水帶翻滾、扭結，如發現有扭轉展現象應及時進行調正。
2, in the status of rubber water stop, we must keep it at the interface part, and even let the rubber water stop roll and twist. If there is a twist, it should be adjusted in time.
