浣跨敤瑾槑Operation Introduction
閵呯７閲枡鏄互閵�銆佺７鍏╁厓鍚堥噾鍜岄妳銆佺７銆侀妧涓夊厓鍚堥噾鐐哄熀鐨勯嚞鏂欙紝瀹冨叿鏈夎壇濂界殑娴佸嫊鎬�锛岄仼鐢ㄤ簬鎺ヨЦ閲剨銆佹埃楂旂伀鐒伴嚞鐒�銆侀珮闋婚嚞鐒婂強鐖愪腑閲剨銆傞妳纾峰悎閲戜腑鍔犲叆閵€鏈冨ぇ澶у湴鎻愰珮鐒婃枡婵曟饯鑳藉姏锛屾彁楂樺挤搴﹀拰闊屾€�锛岄檷浣庣啍榛�銆傚唬娉涙噳鐢ㄤ簬闆诲啺绠�銆佺┖瑾�(di脿o)鍣ㄧ瓑鍒跺喎琛屾キ(y猫)锛屼互鍙婇浕姗�銆侀浕鍣�銆佸剙鍣ㄧ瓑鍒堕€犺妤�(y猫)銆�
閵呯７閲枡閬╁疁浜庨嚞鐒婇妳鍙婇粌閵�锛屼絾鏄笉閬╁疁閲剨榛戣壊閲戝爆銆傞嚞鏂欎腑鐨勭７鍙互閭勫師姘у寲閵呭強姘у寲閵€锛岃捣钁楅嚞鍔戜綔鐢�锛屽洜姝ら妳纾烽嚞鏂欓嚞鐒婇妳鍜岄妧鏅�锛屽彲浠ヤ笉闇€瑕侀嚞鍔�锛屼絾鍦ㄩ嚞鐒婇妳鍚堥噾鏅�锛屽洜鐐虹７涓嶈兘鍏呭垎鍦伴倓鍘熼妳鐨勫悎閲戝厓绱犲舰鎴愮殑姘у寲鐗�锛岀偤浜嗙嵅寰楀劒(y艒u)璩�(zh矛)閲斧锛岄倓鎳夎垏閲姂閰嶅悎浣跨敤銆�
|
The copper-phosphorus filler bls with good fluidity are a kind of copper and phosphorus two elements alloy base or copper,phosphorus and sliver three elements.They can adopt contact welding.oxyfuel gas welding.high frequency welding and furnace welding. The copper-phosphorus alloy with sliver will greatly improve wettability,strength toughness and lower melting point.theseproducts are mainly applied on the refrigeration.air conditioner.water heater as well as transber,motor,instruments and meters etc. Thecopper-phosphorus filler bls are suitable to braze copper,brasses but they can not be suitable to braze ferrous.The phosphorus in the filler bls can reduce oxide of copper and oxde of sliver as braxing flux,so you don`t need it when you braze when you braze copper alloy because the phosphorus can`t fully reduce the oxide bed by copper alloy element. Before brazing,you should b away all dirt on the brazed place and on the surface of b to be brazed such as greasy dirt,oxide and so on,the best brazed joints is between0.03mm to 0.075mm. Theheat speed should be quick as possible when brazing in order to avoid the flat of the filler bls because of slow heat process .The copper color will be reture if it is dipped into 10percent of sulphuric acid solution.
|
閲剨鍓嶅繀闋堝毚鏍兼竻闄ら嚞鐒婇噾灞〃闈㈢殑娌硅剛銆佹哀鍖栫墿绛夋薄鐗�锛岄嚞鐕帴闋殑鏈€濂介枔闅欑偤0.03~0.075mm銆傞嚞鐒婃檪鍔犵啽閫熷害鐩″彲鑳藉揩浜�锛岄伩鍏嶅洜鍔犵啽閬庣▼绶╂參閫犳垚閵呯７閲枡鍋忔瀽锛岀剨鍚庣殑椤忚壊鏄寒鐏拌壊锛屾蹈鍦�10锕～閰镐腑灏囨仮寰╅妳鐨勯鑹�銆�
鐢�(ch菐n)鍝佺殑瑕�(gu墨)鏍�Product Specification
1銆佺剨绲茬郴鍒楋細锟�0.8锝烇繝3.0mm鐩ょ挡锛�
2銆佺剨姊濈郴鍒楋細锟�0.8锝烇繝4.0mm鐩存锛�1.3脳3.15鎵佺剨姊�锛�
