亚洲欧美网站视频,午夜在线激情视频地址一地址二

產品簡介

FD-60型伸縮縫安裝

產品價格：￥1

上架日期：2017-10-10 14:05:58

產地：衡水

發貨地：衡水

供應數量：不限

最少起訂：1米

瀏覽量：135

點擊詢價 QQ洽談

資料下載：暫無資料下載

其他下載：暫無相關下載

詳細說明

FD-60型伸縮縫安裝

1、如要在先攤鋪路面后裝伸縮縫,為保證路面良好的平整度，應該先攤鋪路面，然后開槽安裝伸縮縫。攤鋪路面之前，必須首先清理預留間隙并嵌填泡沫板，再用砂袋或級配砂石袋填實槽口。回填標高以控制瀝青不會污染預埋鋼筋為宜，目的在于防止攤鋪設備壓壞預埋鋼筋，便于路面連續攤鋪。

1, if it is necessary to spread the road before installing expansion joints, in order to ensure a good level of pavement, it should be paved pavement, and then slotted installation expansion joints. Before paving the road, must first b the reserved space and filled with sand filled foam board, or graded sand gravel bag slot. In order to control the elevation of backfill will not pollute the asphalt and pre buried steel should be designed to prevent spreading equipment for crushing and pre buried steel, continuous pavement paving.
2、橋面的切縫、清槽按預留的槽口寬度用切縫機對路面的油面層進行切縫。切縫時應注意保持路面切口完好，無啃邊現象。切縫后及時清除槽內瀝青混凝土及填料，鑿毛槽口內混凝土表面。這一系列工序非常重要，它將影響混凝土的澆筑質量。
2. The cutting seam and the cleaning groove of the bridge are slit with the cutting machine on the b of the reserved notch. Attention should be paid to maintaining good pavement incision and no undercut while cutting. After cutting, clean the asphalt concrete and packing in the slot, and then cut the concrete surface in the notch. This series of processes is very important, it will affect the quality of concrete pouring.

3、在安裝伸縮縫時,下縫前應認真檢查槽內預埋鋼筋，若發現裂縫或折斷，位置不當或間隙過大，必須采取補救措施。要保證沿縫方向每米范圍內至少有1根預埋鋼筋與毛勒伸縮縫的錨環牢固焊接。應該認真檢查XF型橋梁伸縮縫質量，若發現變形或兩鋼梁間距不一致時，應進行修整。必要時，還應根據安裝時的環境溫度調整毛勒伸縮縫的鋼梁間距。應將XF型橋梁伸縮裝置緩緩放入槽內，使縫中心線與實際預留縫中心線相重合，偏差不得超過10mm，同時使鋼邊梁內邊保持垂直。XF型橋梁伸縮縫就位后，應根據縱、橫坡和標高調整其鋼梁頂面比相鄰瀝青混凝土路面低1～2mm，不得超出路面標高。

FD-60型伸縮縫安裝

3, when installing expansion joints, the lower slot should be carefully checked in the pre bded steel bar, if found cracks or broken, improper b or gap is too large, remedial measures must be taken. Make sure that at least 1 bded steel bars and the anchor ring of the expansion joint are firmly welded in the range of the direction of the seam along the seam. The quality of expansion joints of XF bridges should be checked carefully. If the debation or the spacing between the two steel beams is found to be inconsistent, they should be trimmed. When necessary, the spacing between the steel beams of the expansion joint shall be adjusted according to the environmental temperature at the time of installation. The XF type expansion device shall be put into the slot slowly, so that the center line of the joint coincides with the central line of the actual reserved slot, the deviation shall not exceed 10mm, and the inside edge of the steel edge beam shall be kept vertical. After the XF type expansion joint is in place, the top of the steel beam shall be adjusted according to the longitudinal, transverse slope and elevation. The top surface shall be 1 to 2mm lower than that of the adjacent asphalt concrete pavement and shall not exceed the elevation of the road surface.
4、在焊接先點焊部分預埋鋼筋和錨環鋼筋，臨時固定其位置。經檢查符合質量要求后方可將錨環鋼筋與預埋鋼筋焊牢，之后，即可拆除XF型橋梁伸縮縫的裝配夾具。
4, in welding first spot welding part, pre bded steel bar and anchor ring steel bar, temporary fixed b. After inspection to meet the quality requirements before the anchor ring reinforcement and bded steel, welding, assembly fixture can be demolished XF type bridge expansion joint.
5、對于立模、澆混凝土立模應注意模板密封，切忌水泥漿漏入支撐箱，影響支承部件和控制系統的正常工作。澆筑混凝土之前，在錨環內應插入一定數量縱向鋼筋；在鋼邊梁水平肢上加鋪一層鋼筋網；在支撐箱底板上設置雙層防震鋼網。應采用低收縮、快硬、早強混凝土，其標號不得低于上部結構混凝土標號。特別注意錨板、錨環及橫梁支撐箱下面的混凝土密實。在混凝土養護期內，禁止一切車輛通行。
5, for bwork and concrete pouring bwork should pay attention to the template sealing, avoid cement slurry leak into the support box, affect the supporting parts and control system of normal work. Before pouring concrete, a certain amount of longitudinal reinforcement should be inserted into the anchor ring; a layer of reinforcing steel net is added to the horizontal edge of the steel edge beam; a double-layer shock proof steel net is arranged on the bottom plate of the support box. Low shrinkage, quick hardening and early strength concrete shall be adopted, and their grade shall not be lower than that of upper structure concrete. Pay special attention to the concrete density under the anchor plate, anchor ring and cross beam support box. During the maintenance period of the concrete, all vehicles are forbidden to pass.
SGF120橋梁伸縮縫的產品特點如下：
SGF120 bridge expansion joint products are as follows:
1、該橋梁伸縮縫采用擠出成型的Q345（ASTM A709Grade50）型鋼，強度高。型鋼為齒型結構，增加了伸縮量，提高了行車平穩，適用于高速公路及城市道路的橋梁伸縮縫，并能較好地適應橋梁的縱向位移。

1. The expansion joint of the bridge is made of extruded Q345 (ASTM, A709Grade50) steel with high strength. The section steel is a tooth type structure, which increases the expansion amount and improves the running stability. The utility model is suitable for the expansion joint of the highway and the urban road, and can well adapt to the longitudinal displacement of the bridge.

FD-60型伸縮縫安裝

2、此橋梁伸縮縫的伸縮量為0～120mm，介于80mm與160mm的伸縮量之間，避免使用伸縮縫的伸縮量為80mm的伸縮裝置而造成行車不平穩，以及采用伸縮量160mm的伸縮縫而增加工程造價的問題。
2, the expansion of the bridge expansion joint is 0 ~ 120mm, between the expansion amount between 80mm and 160mm, to avoid the use of expansion joint expansion caused by the unstable running as the expansion device of 80mm, and increase the project cost and the amount of expansion joint expansion problem 160mm.
3、采用的錨固系統與GQF－MZLⅡ80相同，適用于各種梁端結構，其預留槽（包括鋪裝層）高度≥150mm。
3, the anchor system and GQF MZL II 80, applicable to all kinds of beam structure, the slot (including pavement) height greater than 150mm.
4、將W型氯丁橡膠伸縮密封條嵌入型鋼內，防水、防塵性能佳。

4, W type neoprene bescopic sealing strip bded in the steel, waterproof and dustproof perbance is good.

FD-60型伸縮縫安裝

在線詢盤/留言

*您的姓名：

*聯系手機：

固定電話：

*聯系郵箱：

所在單位：

*需求數量：

*咨詢內容：

您要求給廠家提供：

免責聲明：以上所展示的信息由企業自行提供，內容的真實性、準確性和合法性由發布企業負責，本網對此不承擔任何保證責任。我們原則上建議您選擇本網高級會員或VIP會員。

企業信息

河北瑞博橡塑制品有限公司

會員級別：

------------ 聯系方式 ------------

聯系人：王偉（先生）

聯系電話：0318-2110875

聯系手機：13166570832

傳真號碼：0318-2110875

企業郵箱：3407742055@QQ.COM

網址：hsribo.jdzj.com

郵編：53500

企業網站

進入商鋪

WWW国产精品内射老熟女,亚洲无码成人综合网,AV美女主播高潮,无码图片二区