国产精品久久久久久久久,四季AV一区二区夜夜嗨,日韩精品无码中文字幕电影,www.五月婷婷.com

Release (only as spare part)
(product status: Cancellation/discontinuation):

6FC5357-0BB23-0AA0


(predecessor:
6FC5357-0BB22-0AE0)

SINUMERIK 840DE
NCU 572.3, 400 MHZ, 64 MB
WITHOUT SYSTEM SOFTWARE
MEMORY: NC 0.5MB, PLC 96KB
PROFIBUS-DP PREPARED
ACCORDING TO IEC 61508

6FC5357-0BB33-0AA0


(predecessor:
6FC5357-0BB33-0AE3)

SINUMERIK 840D/DE
NCU 573.3, 650 MHZ, 64 MB
WITHOUT SYSTEM SOFTWARE
MEMORY: NC 2.5MB, PLC 96KB
PROFIBUS-DP PREPARED
ACCORDING TO IEC 61508

  Hardware

NCU system software, compatibility subsequently tested

  NCU 572.3

6FC5357-0BB22-0AE0

   12-axis software:
  6FC520-_BY30-_AH_
  6FC520-_BX30-_AH_

  SW4.4 from V04.04.38
  SW5.3 from V05.03.08
  all SW6.x

6FC5357-0BB23-0AA0

  SW4.4 from V04.04.39
  SW5.3 from V05.03.42
  all SW6.x

  NCU 573.3

6FC5357-0BB33-0AE2

  12-axis software:  
  6FC520-_BY30-_AH_
  6FC520-_BX30-_AH_

  31-axis software:
  6FC520-_AY30-_AH_
  6FC520-_AX30-_AH_

   all SW4.x
  all SW5.x
  all SW6.x
  all SW7.x

6FC5357-0BB33-0AE3

  SW4.4 from V04.04.39
  SW5.3 from V05.03.18
  all SW6.x
  all SW7.x
  (see also !18682807!)

6FC5357-0BB33-0AA0

  SW4.4 from V04.04.39
  SW5.3 from V05.03.42
  all SW6.x
  SW7.2 from 07.02.07

PLC beters

315-2DP
NCU *.3

314C-2DP
NCU *.4

317-2DP
NCU *.5

Processing time in ms/kI (1 kI = 1024 instructions, corresponds to approx. 3 kbytes)
- for bit commands (minimum)
- for commands (minimum)
Factor for cycle time for
user programs ¹⁾

0.3
1.0

1

0.1
0.25

0.35

0.03
0.1

0.12

PLC user memory in kbytes,
basic version
max. expansion

96
288

96
480

128
768

No. of FBs, FCs

Each 256

Each 256

2048 ²⁾

No. of DBs

399

399

2047²⁾

No. of timers

128

256

512

No. of counters

64

256

512

I/O scope for cyclic process image

Each 128

    Each 128

Each 256

I/O scope for the complete logical I/O address space

Each 1024

Each 1024

Each 4096 ³⁾

Max. number of Profibus slaves

63

32

125

Comments:

1)

The increase in perbance refers to the computational perbance available. Depending on the technological/process-related conditions, this increase in perbance is included in the total result. A faster IPO clock cycle (as a result of faster processors) and lower PLC cycle times result, partially, in significantly improved technological/process-related results; e.g. shorter unit/clock cycle times, higher speeds for eccentric turning, higher feed rates for mould construction.

2)

The number specified is the upper address number that can be used; the maximum number of FBs, FCs and DBs is, as a total, 2048!
Reserved addresses should be taken into account; refer to the current documentation.

3)

4096 additional I/O addresses are available and can be seen in STEP 7; however these addresses are reserved for future applications. For compatibility reasons, these addresses may not be used. 
The diagnostic addresses (presently at the upper end 1023, 1022) must be appropriaby marshaled in the PLC project; refer to the current documentation.