The following explanations supports this endeavours with regards to correct bs for unintentional and undesired debation of fabric conveyor belts.下面的解釋方面無意的和不受歡迎的織物輸送帶變形的正確表達式支持這種努力 。
Note: Do not use the b “curved belt” to describe undesired belt debation, because this is typically used to refer to powerturn belts.注意： 不要使用“弧形地帶”來形容不受歡迎的皮帶變形，因為這是通常用來指powerturn安全帶。
Cambered belt (“banana shape”)弧形帶（“香蕉形狀”） A cambered belt is characterized by a longitudinal curvature of the belt relative to its centerline due to different internal stresses:一個弧形帶的特點是由一個帶相對其中心線，由于不同的內部應力的縱向曲率：
Camber can be caused by可引起康貝 • the manufacturing process•在制造過程 • environmental conditioning of the material (namely with belts with polyamide trb layer due to hygroscopic behaviour)•環(huán)?？照{的物質（即聚酰胺牽引層由于帶的吸濕行為 ） • improper storage ie storing belt on its edge (different conditioning over the coil b, one belt edge gets longer than the other)•儲存不當，即存儲在其邊緣帶（在線圈寬度不同的空調，一個帶的邊緣變得長于其他 ）
Common colloquialism for belt camber is “banana effect” or “banana belt”.帶拱常見的俗語是“香蕉效應”或“香蕉帶”。
Joint (splice) misalignment聯合（拼接）不對 Joint (splice) misalignment is commonly the result of improperly squared belt ends.聯合（拼接）不對通常不當平方帶兩端的結果 。This effect is seen as a cyclic lateral drifting of the belt as the joint (splice) approaches and passes a reference point on the conveyor:這種效應被看作是一個循環(huán)的橫向聯合（拼接）方法帶漂流，并通過一個傳送帶上的參考點：
Joint (splice) misalignment can also be caused by an improper slitting, if the end of the belt leaves the constraint of the guides that direct the belt into the slitter:聯合（拼接）不對也可以造成不當的縱切，如果傳送帶末端離開導游直接帶分切機的約束：
Edge cbing卷邊Habasit(哈伯斯特) Edge cbing is characterized by a transversal concave or convex dished belt ed ges :卷邊的特點是由橫向的凹或凸拋出帶版 GES：
Belt cupping (or dishing)腰帶拔罐（或拋出）Habasit(哈伯斯特) Belt cupping, also called dishing, is characterized by an unintentional transversal concave or convex belt dishing over the whole belt b:腰帶拔罐，也被稱為凹陷，特點是由無意的橫向凹或凸的皮帶在整個皮帶寬度拋出 ：
Belt waving皮帶揮舞Habasit(哈伯斯特) Belt waving皮帶揮舞is characterized by longitudinal waves, which propagate across the belt's b :縱波，它傳播到皮帶的寬度的特點是 ：
Belt buckling帶屈曲 Belt buckling帶屈曲is the bation of a longitudinal ridge in the belt typically along the centre of the belt b.是一個在腰帶上，通常沿皮帶寬度的中心的縱脊的形成。In extreme cases the buckled belt may overlap/fold over :在極端情況下扣皮帶可能會重疊/倍以上：
Belt edge rippling帶的邊緣蕩漾Habasit(哈伯斯特) Edge rippling is characterized by longitudinally corrugated edges:邊緣縱向波紋邊蕩漾著的特點是：
