該系列雙電源自動轉換開關主要由兩臺具有高分?jǐn)嗄芰Φ腉TM1系列斷路器及本公司自行研制的雙電源自動轉換開關控制器等組成，適用于額定電壓400V、50Hz，額定電流800A及以下的高層建筑、醫院、商場、銀行、消防、化工、冶金、軍事設施等不允許斷電的一類負荷，部分二類負荷，完成雙回路供電系統的電源自動轉換，從而保證重要用戶供電的可靠性。
本產品符合GB/T14048.11-2002 IEC60947-6-1(1998)《自動轉換開關電器》標準。
2.正常工作條件
·安裝的海拔高度不應超過2000米。
·周?chē)h(huán)境溫度上限不高于+40℃，下限不低于-5℃，24小時平均值不超過+35℃。
·大氣的相對濕度在周?chē)諝鉁囟葹?40℃時不超過50％，在較低的溫度下，可以有較高的濕度，應考慮到溫度變化會發生產品表面的凝霜。
·無爆炸危險的介質，且介質無足以腐蝕和破壞絕緣的氣體與塵埃。
·無顯著搖動和沖擊震動的地方。
3.安裝及接線方法
接線時常用電源N應接入常用電源執行斷路器QN，備用電源日應接入備用電源執行斷路器QR。當QN和QR為四線斷路器時，接線方式按接線圖，其中QN和QR的1，3，5為三相(A．B、C)進線端，2、4，6為三相出線端，7為零線(N)進線端，8為零線出線端。
若選用斷路器為三極斷路器，則必須將常用電源(N)的零線NN和備用電源(R)的零線NR同時接到三極專用接零線端子KG上。具體操作見接線圖。雙電源切換開關自動控制器的工作電源取斷路Q(chēng)N和QR的進線端A相和零線N，若選用斷路器為三極斷路器時，必須要接零線NN和NR，該三極專用接線零端子在兩臺斷路器中間，在自動電源切換開關安裝，接線過程中，切不要把原接在斷路器進線端的本機控制器線忘掉，碰斷或短路等。
4.使用操作
無論常用電源和備用電源有無電壓，均可采用手動操作方式。手動操作時，應將手動-自動按鈕置于手動操作位置，當推動手柄順時針旋轉至終端時，備用電源執行斷路器QR分閘，常用電源執行斷路器QN合閘；當推動手柄逆時針旋轉至終端時，備用電源執行斷路Q(chēng)R合閘，常用電源執行斷路器QN分閘。
面板中，電源指示燈(紅)，若該燈不亮，說明自動控制盒工作電源有故障，不能操作開關。待修復正常后，將手動·自動按鈕冒于自動位冒狀態，如果常用電源供電正常，切換開關將自動投入常用電源執行斷路器QN合閘狀態，面板中N電指示燈(黃)亮；如果常用電源供電不正常，則切換開關將自轉換到備用電源QR供電，備用電源日指示燈(綠)亮。
6 warning For your safety and equipment, please read the following: Carefully read the operating rules, and strictly comply with the operating rules, should avoid causing serious losses. Oath to those who do not regulate the operation of the equipment caused serious losses. Do not plug the controller plug, otherwise it will lead to electric shock hazard or product damage Non professional personnel to prohibit the operation or modification, otherwise it will cause an electric shock hazard or product damage This product users do not need to change, otherwise it will result in product damage - load capacity can not exceed the rated capacity of the switch, otherwise it will lead to switch tripping or burn And can not be zero line (n) phase error access circuit breaker, the two b must be consistent with a circuit breaker, the normal power supply (NN) and the standby power supply (RN) with when the zero line to the terminal (KG) pin 1 (n), otherwise it will lead to damage to the switch. The ground should be reliable, to ensure safe use Can not be directly installed in the outdoor work, or shorten the service life or cause adverse rebs Can not be directly installed in flammable and explosive, wet, direct sunlight, high temperature, vibration, shock and other places. Otherwise, it will shorten the service life or cause the product combustion explosion. Can not be directly installed in the conductive dust, bl wire intrusion, otherwise it will result in product damage or mechanical failure. Should meet the requirements of the sample, otherwise it will shorten the service life. 1 scope of application The double power series dual power automatic transfer switch is mainly composed of two sets of high breaking capacity of the GTM1 series circuit breaker and the company self-developed automatic switch controller, the rated voltage of 400V and 50Hz, a kind of load rated current 800A and below the high-rise buildings, hospitals, shopping malls, banks, and fire chemical industry, bllurgy, military facilities are not allowed to power, part of the two types of load, power supply double circuit power supply system automatically, so as to ensure the reliability of the important power supply
