国产精品久久久久久久久,四季AV一区二区夜夜嗨,日韩精品无码中文字幕电影,www.五月婷婷.com

The CP 1243-1 DNP3 communications processor is used to connect a SIMATIC S7-1200 to a control center system via the DNP3 protocol and has the following characteristics:

• Support for the established DNP3 becontrol protocol for standardized bing of the SIMATIC S7-1200 to WinCC, PCS 7, or other commercially available control center systems
• Data transfer of measured values, control variables, or alarms optimized for becontrol systems
• Automatic sending of alert emails
• Clearly laid out LED signaling for fast and easy diagnostics
• Compact industrial enclosure in S7-1200 design for mounting on a standard mounting rail
• Fast commissioning thanks to easy configuration using STEP 7
• Data buffering of up to 64,000 values ensures a secure database even with temporary connection failures

• Data security
  The CP 1243-1 DNP3 has a large buffer for several thousand data values. Downtimes in the transmission b can then be bridged.
• Fully automatic time stamp
  To enable subsequent and correct archiving of process data in the control system, all data frames are assigned with a time stamp at their place of origin.
• Fast and flexible data communication
  Operators are therefore quickly provided with alarms, statuses and values from the process, and they can influence process control by entering commands or setpoints at any time.
• Simple and low-cost engineering
  The cyclic or event-controller transfer of measurements, setpoints or alarms can be implemented in only a few operations and without programming effort.
• Remote diagnostics
  Saving of traveling and maintenance costs due to cost-effective remote programming, diagnostics, control and monitoring via the Internet

• Plants in water, wastewater or environmental sectors:
  • Irrigation systems
  • Drinking water supply
• Monitoring of power networks for consumption metering and cost control
  • District heating networks
  • Wind farms
• Plants in the oil and gas sector
  • Oilfield water injection
  • Pipelines

By using the CP 1243-1 DNP3, the S7-1200 can be used as a remote terminal unit (substation) in becontrol applications. Typical uses include the collection of measured values in geographically widely distributed outdoor areas (level measurement for water tanks) or centralized opening and closing of valves (oil/gas transport in pipelines).

The CP 1243-1 DNP3 offers all the advantages of the S7-1200 design:

• Rugged, compact plastic enclosure
• Easily accessible connection and diagnostics elements, protected by front flaps
• Simple mounting on the mounting rail of the S7-1200

The CP 1243-1 DNP3 is plugged into the left-hand system bus interface of the S7-1200. Power is supplied directly via the S7-1200. No additional wiring is necessary. Any required modems or routers are connected via the Ethernet interface on the underside of the module.

The CP 1243-1 DNP3 is a communication module for the S7-1200. The module allows the S7-1200 to be connected as a remote station to a DNP3-based control center in just a few steps.

Compleby configurable application through "data point configuration"

The introduction of the "data point configuration" in STEP 7 dispenses with all programming effort for transfer of data to the control center.

The data of the CPU relevant to the control center is selected via user-friendly "item browsing" in STEP 7. In a bly-arranged menu, the data transfer beters are then assigned to the data points selected in this way. The cyclic or event-controller transfer of measurements, setpoints or alarms can thus be implemented in only a few operations and without programming effort.

Data backup

Data losses are prevented by the data buffering mechanisms integrated in the product.

In the event of a connection failure, up to 64,000 time-stamped values are buffered. When the connection returns, the buffered values are automatically transferred to the control center in the right order.

E-mail alerting

Alert e-mails can be configured for timely provision of stations' states to service or maintenance personnel. If previously defined events (such as threshold violation) should occur, application-specific inbation is sent automatically by e-mail.

Diagnostics

The CP 1243-1 DNP3 offers comprehensive diagnostic options for a quick and inbative analysis of the station status. Elementary diagnostic inbation about the connection to the control center is signaled directly via LEDs at the CP.

Using STEP 7, comprehensive inbation can be retrieved, such as connection history, buffer status, and the transferred measured values.

DNP3 protocol

Communication with the control center is based on the established standard of DNP3 specification 2 (2007/2009).

Thanks to support of the b and data transfer mechanisms defined in the specification, compatibility with PCS 7, WinCC (with applicable becontrol packages), and all other control center systems available on the market is warranted.

The security mechanisms already defined in the DNP3 standard for secure data transfer through trunk networks are fully supported.

Remote maintenance

For remote access from the control center to the substation, the CP provides a remote maintenance port in parallel with process operation. This ensures access for monitoring and program changes.

Interfaces

The CP 1243-1 DNP3 has an Ethernet interface to connect to the control center. The S7-1200 can be connected via an existing network or via other media by using additional routers (e.g. SCALANCE M for mobile wireless communication).

Power supply

Extra wiring for the CP power supply is not required. Power is supplied directly via the backplane bus of the S7-1200.

CP 1243-1 DNP3 with 3rd-party control center

CP 1243-1 DNP3: Integration in existing becontrol systems

CP 1243-1 DNP3 with PCS 7 control center