FOR INSTALLATION
1.To install stainless steel wire ,the angle of wire should be got proper and minimal,the allow tolerance is at+/-30.
2.To make sure that the hook of the stainless steel wire does not exceed the measurement range ,otherwise ,the wire will be to break off or you will get inferior accuracy.
3.The wire is stainless steel with fluorin coating.You will get inferior accuracy if the wire is damaged or stretched excessively.
4.You can move the linear sensor instead of the wire.
5.If your application is not linear motion,please set the pulley to smooth the rotation.
6.If the products work under serious environments,such as oil,water ,heavy dust,iron chipping or shavings or any powder can cause to hurt the wire,please make more protective cover or other equipment.
7.The acceleration for CPS-S-P and CPS-M-P series is under 1m/sec.max;the acceleration for CPS-L-P and CPS series is under 0.5m/sec.max.
安裝注意事項
１．利用底部４個固定螺絲孔,依現場及機器安裝空間設施需要,直接安裝或另加保護或其他機械使用．
２．不銹鋼索安裝時,須注意水平角度,亦即盡量使鋼索由出線口至移動部位之機構,于工作時水平滑動，
保持最小角度（容許偏差＋/-３0）以確保量測精度及鋼索之壽命．
３．鋼索本體是不銹鋼加涂氟層,請勿讓其受外力的割傷﹑燒損﹑撞擊等不當之事發生：過量的粉塵﹑積屑或是足以破壞鋼索的物品貯留于內部的滑輪或出線口將造成鋼索破損,導致運轉不順的故障．
４．未安裝于工作臺或固定坐前,請勿用手或是其它產品將鋼索拉出并讓其瞬間自行彈回．此舉將造成鋼索斷裂,傷害本體結構及人身安全．
５．CPS-S和CPS-M系列產品的往復運動的瞬間加速絕對不可超過1米／秒；CPS-L和CPS-L-P系列產品的往復運動的瞬間加速絕對不可超過0.5米／秒；此舉將造成鋼索斷裂，恕本公司不承擔此范圍以外的責任．
６．若使用于非直線運動的機構,請加裝適當?shù)幕嗊\轉．
７．若使用于環境惡劣或特殊場合,請自行加裝保護機構或與本公司工程部、經銷商洽談、否則造成產品損壞,本公司不予以負責．
Introduction to linear wire potentiometer /encoder
Linear wire potentiometer /encoder is a ingenious combination of rotary sensors and linear sensors ,with longer sensing scope ,same measurement precise ,smaller structure ,which are widely adopted by customers from different fields .this series of sensors have sensing scope from 200mm to 20000mm,with output of analog current signal 4~20mA , anolog voltage signal 0~5V or o~10V and digital pulse A、B、Z phase signal output.
OEM orders are warmly welcome。
拉繩位移傳感器是一款安裝方便，簡單應用的高精度，高穩定性，的傳感器。它采用一體式的鋁合金結構，輕便，堅固，主要傳感器件采用美國BOURNS多圈電位器，德國倍加福編碼器，耐磨，線性精度，重復性精度，及阻抗特性方面均高度可靠，同時帶有絕對值和增量編碼器型輸出方式，兩部分的緊密配合，既保證產品的可靠性，又同事輸出高精度的方波與數字信號。最高精度有可達到0.01%。 Effective Stroke(mm)量測行程 (100mm~1000mm)之間量程任意可選 Output Signal Mode輸出信號模式 Resistance(Potentiometer) 0-10V, 0-5V,4-20mA Linearity線性度 ±0.25%FS(standard class);±0.10%FS(precision class) Repeatability重複性 ±0.02%FS Resolution解析 Essentially infinite本質無窮 Sensor傳感器 Wire-winding and hybrid potentiometer繞線混合電位器 Input Resistance輸入電阻值 5Kohm±10%FS(standard class),±5%FS(precision class) Recommended Input Voltage輸入電壓 30VDCmax.,best voltage at5/10Vdc Power Rating(watts)額定功率 Wat70℃ Max.Measuring Wire Velocity( go and back )最大往復速度 600mm/sec Starting force拉力 ≦2200g Measurement Wire線徑規格 Diameter1mmSUS304 with fluorin-coated Weight重量 ≤3500g Operating Temp.工作溫度 0℃～+70℃ Storage Temperature儲存溫度 -20℃～+80℃ Vibration震動 10Hz to 2000Hz Protection保護等級 IP67
