拉繩位移傳感器，位移傳感器Electronics 電路特性 電壓型,Open Collector電流型,Push Pull推挽式,差動式
拉繩位移傳感器，位移傳感器Power supply工作電壓 DC12-28V ,DC5Vfixed
拉繩位移傳感器，位移傳感器Current consumption消耗電流 ≦30mA
拉繩位移傳感器，位移傳感器Output Capacity輸出容量 Sync .current:20mA, Residual voltage:0.5V or less
拉繩位移傳感器，位移傳感器Max Response最大響應頻率 10kHz~180kHz
拉繩位移傳感器，位移傳感器Phase different相位差 A,Bphase different 90℃±45℃(T/4±T/8),ZphaseT±T/2
FOR INSTALLATION
1.To install stainless steel wire ,the angle of wire should be got proper and minimal,the allow tolerance is at+/-30.
2.To make sure that the hook of the stainless steel wire does not exceed the measurement range ,otherwise ,the wire will be to break off or you will get inferior accuracy.
3.The wire is stainless steel with fluorin coating.You will get inferior accuracy if the wire is damaged or stretched excessively.
4.You can move the linear sensor instead of the wire.
5.If your application is not linear motion,please set the pulley to smooth the rotation.
6.If the products work under serious environments,such as oil,water ,heavy dust,iron chipping or shavings or any powder can cause to hurt the wire,please make more protective cover or other equipment.
7.The acceleration for CPS-S-P and CPS-M-P series is under 1m/sec.max;the acceleration for CPS-L-P and CPS series is under 0.5m/sec.max.
安裝注意事項
１．利用底部４個固定螺絲孔,依現場及機器安裝空間設施需要,直接安裝或另加保護或其他機械使用．
２．不銹鋼索安裝時,須注意水平角度,亦即盡量使鋼索由出線口至移動部位之機構,于工作時水平滑動，
保持最小角度（容許偏差＋/-３0）以確保量測精度及鋼索之壽命．
３．鋼索本體是不銹鋼加涂氟層,請勿讓其受外力的割傷﹑燒損﹑撞擊等不當之事發生：過量的粉塵﹑積屑或是足以破壞鋼索的物品貯留于內部的滑輪或出線口將造成鋼索破損,導致運轉不順的故障．
４．未安裝于工作臺或固定坐前,請勿用手或是其它產品將鋼索拉出并讓其瞬間自行彈回．此舉將造成鋼索斷裂,傷害本體結構及人身安全．
５．CPS-S和CPS-M系列產品的往復運動的瞬間加速絕對不可超過1米／秒；CPS-L和CPS-L-P系列產品的往復運動的瞬間加速絕對不可超過0.5米／秒；此舉將造成鋼索斷裂，恕本公司不承擔此范圍以外的責任．
６．若使用于非直線運動的機構,請加裝適當?shù)幕嗊\轉．
７．若使用于環境惡劣或特殊場合,請自行加裝保護機構或與本公司工程部、經銷商洽談、否則造成產品損壞,本公司不予以負責．
