| 瑭崇窗鍙冩暩(sh霉) | |||
|---|---|---|---|
| 鍝佺墝/寤犲 | 鍩虹(ch菙)鍓�(chu脿ng)鏂板鏂�(缇庡湅) | 鐗岃櫉 | 2210EPR |
| 椤炲瀷 | 姝ｇ墝鏂� | 鍔犲伐绱氬垾 | 娉ㄥ皠绱� |
| 鐔旈珨娴佸嫊閫熺巼 | 123g | 瀵嗗害 | 1.42g |
| 鎷変几寮峰害 | 23kg | 褰庢洸寮峰害 | 145kg |
| 褰庢洸妯￠噺 | 23kg | 缂哄彛娌栨搳寮峰害 | 4kg.cm |
| 鏂疯浼搁暦鐜� | 2% | 鎴愬瀷鏀剁府鐜� | 3% |
| 娲涙皬纭害 | 114HR | 鐔辫畩褰㈡韩搴� | 198鈩� |
| 鑴嗗寲婧害 | 6鈩� | 缍崱杌熷寲榛� | 218.89掳F |
| 鐗规€х礆鍒� | 鐔辩┅(w臎n)瀹氭€� 鎶楀寲瀛告€� 闃荤噧绱� 澧炲挤绱� 鑰愰珮婧� 鑰愪綆婧� 鑰愭按瑙� 鑰愯€佸寲 楂樺挤搴� 楂樺墰鎬� 鑰愮（ 鑰愬€� | 鐢ㄩ€旂礆鍒� | 闆诲瓙闆诲櫒閮ㄤ欢 闆诲嫊宸ュ叿閰嶄欢 姹借粖閮ㄤ欢 瀹堕浕閮ㄤ欢 |
| 鐢�(ch菐n)鍦� | 缇庡湅 | ||
鍏�(n猫i)閮ㄨ劔妯＄幓绾栧～鍏匬EI ULTEM 2210EPR
ULTEM Resin 2210EPR |
PEI 鍩虹(ch菙)鍓�(chu脿ng)鏂板鏂欙紙缇庡湅锛�2210EPR
ULTEM 2210EPR
20%鐜荤拑绾栫董濉厖,楂樻祦閲廝olyetherimide(Tg 217 c)鑸囧収(n猫i)閮ㄨ劔妯″拰澧炲挤electroplatability銆�绗﹀悎寮楀悏灏间簽宸濫CO锛岄樆鐕僓L94-V0鍜�5VA 銆傛敞灏勬垚鍨�銆�
鍏稿瀷鐨勫爆鎬э細
| MECHANICAL | Value | Unit | Standard |
| Tensile Stress, brk, Type I, 5 mm/min | 1330 | kgf/cm2 | ASTM D 638 |
| Tensile Strain, brk, Type I, 5 mm/min | 4 | % | ASTM D 638 |
| Tensile Modulus, 5 mm/min | 70300 | kgf/cm2 | ASTM D 638 |
| Flexural Stress, brk, 2.6 mm/min, 100 mm span | 2320 | kgf/cm2 | ASTM D 790 |
| Flexural Modulus, 2.6 mm/min, 100 mm span | 70300 | kgf/cm2 | ASTM D 790 |
| Hardness, Rockwell M | 114 | - | ASTM D 785 |
| IMPACT | Value | Unit | Standard |
| Izod Impact, unnotched, 23掳C | 49 | cm-kgf/cm | ASTM D 4812 |
| Izod Impact, notched, 23掳C | 6 | cm-kgf/cm | ASTM D 256 |
| Izod Impact, Reverse Notched, 3.2 mm | 47 | cm-kgf/cm | ASTM D 256 |
| THERMAL | Value | Unit | Standard |
| Vicat Softening Temp, Rate B/50 | 220 | 掳C | ASTM D 1525 |
| HDT, 0.45 MPa, 6.4 mm, unannealed | 210 | 掳C | ASTM D 648 |
| HDT, 1.82 MPa, 6.4 mm, unannealed | 210 | 掳C | ASTM D 648 |
| CTE, -20掳C to 150掳C, flow | 2.52E-05 | 1/掳C | ASTM E 831 |
| Relative Temp Index, Elec | 170 | 掳C | UL 746B |
| Relative Temp Index, Mech w/impact | 170 | 掳C | UL 746B |
| Relative Temp Index, Mech w/o impact | 170 | 掳C | UL 746B |
| PHYSICAL | Value | Unit | Standard |
| Specific Gravity | 1.42 | - | ASTM D 792 |
| Water Absorption, 24 hours | 0.19 | % | ASTM D 570 |
| Water Absorption, equilibrium, 23C | 1.1 | % | ASTM D 570 |
| Mold Shrinkage, flow, 3.2 mm (5) | 0.3 - 0.5 | % | SABIC Method |
| Melt Flow Rate, 337掳C/6.6 kgf | 6 | g/10 min | ASTM D 1238 |
| ELECTRICAL | Value | Unit | Standard |
| Volume Resistivity | 7.E+16 | Ohm-cm | ASTM D 257 |
| Dielectric Strength, in oil, 1.6 mm | 26.3 | kV/mm | ASTM D 149 |
| Relative Permittivity, 1 kHz | 3.5 | - | ASTM D 150 |
| Dissipation Factor, 1 kHz | 0.0015 | - | ASTM D 150 |
| Dissipation Factor, 2450 MHz | 0.0049 | - | ASTM D 150 |
| Arc Resistance, Tungsten {PLC} | 6 | PLC Code | ASTM D 495 |
| Hot Wire Ignition {PLC) | 1 | PLC Code | UL 746A |
| High Voltage Arc Track Rate {PLC} | 2 | PLC Code | UL 746A |
| High Ampere Arc Ign, surface {PLC} | 4 | PLC Code | UL 746A |
| Comparative Tracking Index (UL) {PLC} | 4 | PLC Code | UL 746A |
| FLAME CHARACTERISTICS | Value | Unit | Standard |
| UL Recognized, 94V-0 Flame Class Rating (3) | 0.4 | mm | UL 94 |
| UL Recognized, 94-5VA Rating (3) | 1.9 | mm | UL 94 |
| Oxygen Index (LOI) | 50 | % | ASTM D 2863 |
| NBS Smoke Density, Flaming, Ds 4 min | 1.3 | - |
ASTM E 662 |
