| 詳細參數 | |||
|---|---|---|---|
| 品牌 | Emerson | 型號 | 57C404C |
| 結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
| LD指令處理器 | 硬PLC | 功能 | 網絡通信模塊 |
| 工作電壓 | 電源組24VDC | 處理速度 | 1.6GHz |
| 程序容量 | 4GB | 數據容量 | 1GB |
| 產品認證 | UL | 環境溫度 | -40°Cto70°C |
| 環境濕度 | 5%to95%RH | 加工定制 | 否 |
Reliance Electric 57C404C 網絡通信模塊
57C404C具有很完善的自診斷功能，如出現故障，借助自診斷程序可以方便的找到出現故障的部件，更換后就可以恢復正常工作。故障處理的方法可參看PLC系統手冊的故障處理指南。實踐證明，外部設備的故障率遠高于PLC，而這些設備故障時，57C404C不會自動停機，可使故障范圍擴大。為了及時發現故障，可用梯形圖程序?qū)崿F(xiàn)故障的自診斷和自處理。
機械設備在各工步的所需的時間基本不變，因此可以用時間為參考，57C404C在可編程控制器發出信號，相應的外部執行機構開始動作時起動一個定時器開始定計時，定時器的設定值比正常情況下該動作的持續時間長20%左右。57C404C如某執行機構在正常情況下運行10s后，使限位開關動作，發出動作結束的信號。在該執行機構開始動作時起動設定值為12s的定時器定時，若12s后還沒有收到動作結束的信號，由定時器的常開觸點發出故障信號，該信號停止正常的程序，起動報警和故障顯示程序，使操作人員和維修人員能迅速判別故障的種類，及時采取排除故障的措施。
57c404c has perfect self diagnosis function. In case of fault, the fault parts can be easily found with the help of self diagnosis program, and the normal operation can be restored after replacement. For troubleshooting bs, please refer to the troubleshooting guide in the PLC system manual. Practice has proved that the failure rate of external equipment is much higher than that of PLC. When these equipment fail, 57c404c will not stop automatically, which can expand the failure range. In order to find faults in time, ladder program can be used to realize fault self diagnosis and self-treatment.
The required time of mechanical equipment in each work step is basically unchanged, so time can be used as a reference. 57c404c starts a timer to start timing when the programmable controller sends a signal and the corresponding external actuator starts to act. The set value of the timer is about 20% longer than the duration of the b under normal conditions. 57c404c if an actuator operates for 10s under normal conditions, make the limit switch act and send the signal of end of b. When the actuator starts to act, start the timer with the set value of 12s. If the signal of b end is not received after 12s, the normally open contact of the timer sends a fault signal, which stops the normal program and starts the alarm and fault display program, so that the operators and maintenance personnel can quickly identify the type of fault and take troubleshooting measures in time.
ABB 3HNA025019-001
GE CR215GH87
A-B 1785-ME64/A
AMAT 0190-09379
Sime-Stromag 4205(405227)
KOLLMORGEN S20330-SRS
EATON XV-440-10TVB-1-10
EMERSON KJ4002X1-BE1
B&R 3CP260.60-1
ABB CI858
ABB DSPC174 3BSE005461R1
ABB DSBB110A 57330001-Y
ABB DSMB127 57360001-HG
ABB PFSK130 3BSE002616R1
ABB DSCA114 57510001-AA
ABB DSCS131 57310001-LM
ABB PFSK160A 3BSE009514R1
ABB PFSK162 3BSE015088R1
ABB PFSK164 3BSE021180R1
ABB DSMC112 57360001-HC
ABB DSBC172 57310001-KD
ABB DSRF180A 57310255-AV
ABB DSSR122 48990001-NK
ABB DSSB140 48980001-P
ABB DSTC175 57310001-KN
ABB GRBTU 3BSE013175R1
