| 詳細參數 | |||
|---|---|---|---|
| 品牌 | BENTLY | 型號 | 350053 |
| 結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
| LD指令處理器 | 其他 | 功能 | 超速檢測模塊 |
| 工作電壓 | 電源組24VDC | 輸出頻率 | 47to63Hz |
| 環境溫度 | -40°Cto,85°C | 環境濕度 | 5至95%,非冷凝 |
| 加工定制 | 否 | 重量 | 3磅 |
| 產地 | 美國 | ||
Bently 本特利 350053 超速檢測模塊
Bently350053：
（1）分配、定義PLC的I/O點，繪制I/O連接圖。根據選用的PLC所給定的元件地址范圍（如輸入、輸出、輔助繼電器、定時器、計數器。數據區等），對控制系統使用的每一個輸入、輸出信號及內部元件定義專用的信號名和地址，在程序設計中使用哪些內部元件，執行什么功能格都要做到清晰，無誤。
（2）Bently350053控制程序設計。包括設計梯形圖、編寫語句表、繪制控制系統流程圖?？刂瞥绦蚴强刂普麄€系統工作的軟件，是保證系統工作正常，安全?？煽康年P(guān)鍵，因此，控制程序的設計必須經過反復測試。修改，直到滿足要求為止。
（3）控制柜（臺）設計和現場施工。在進行控制程序設計的同時，可進行硬件配備工作，主要包括強電設備的安裝、控制柜（臺）的設計與制作、可編程序控制器的安裝、輸入輸出的連接等。在設計繼電器控制系統時，必須在控制線路設計完成后，才能進行控制柜（臺）設計和現場施工?？梢姡捎?/span>Bently350053控制系統，可以使軟件設計與硬件配備工作平行進行，縮短工程周期。如果需要的話，尚需設計操作臺、電氣柜、模擬顯示盤和非標準電器元部件。
Assign and define I / O points of PLC and draw I / O connection diagram. According to the element address range given by the selected PLC (such as b, output, auxiliary relay, timer, counter, data area, etc.), define the special signal name and address for each b, output signal and internal element used by the control system, which internal elements are used in the program design, and what function grid is executed should be b and correct.Bently350053 control program design. It includes designing ladder diagram, writing statement table and drawing control system flow chart. The control program is the software that controls the work of the whole system and ensures the normal and safe operation of the system. Reliable key, therefore, the design of control program must be tested repeatedly. Modify until the requirements are met.
Control cabinet (set) design and site construction. While designing the control program, the hardware can be equipped, mainly including the installation of strong current equipment, Bently350053 the design and manufacture of control cabinet (console), the installation of programmable controller, the connection of b and output, etc. When designing the relay control system, the control cabinet (set) design and field construction can only be carried out after the control circuit design is completed. It can be seen that the use of Bently350053 control system can make the software design parallel to the hardware configuration and shorten the project cycle. If necessary, operation console, electrical cabinet, analog display panel and non-standard electrical components need to be designed
ABB PFEA112-65 3BSE050091R65
A-B 1747-L552/A
A-B 1747-L553/A
ABB LXN1604-6 3BHL000986P7000
SST SST-PB3-CLX
METSO IOP114
A-B 81001-450-53-R
A-B 80190-580-01-R
ABB CMA120 3DDE300400
ABB 5SHY3545L0010 3BHB013088R0001
BENTLY 3500/40M 176449-01
BENTLY 3500/60 163179-01
AUTOTECH CONTROLS SAC-RL100-M11T
BENTLY 3500/50-01-00
A-B 80026-044-06-R
EPRO PR6423/010-040+CON021
SIEMENS 6ES7408-1TB00-0XA0
