詳細參數 | |||
---|---|---|---|
品牌 | MOTOROLA | 型號 | MVME2100 |
結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
LD指令處理器 | 硬PLC | 工作電壓 | 電源組24VDC |
輸出頻率 | 25MHz | 處理速度 | MPC755處理器,400MHz |
程序容量 | 4MB | 產品認證 | CQ |
環(huán)境溫度 | 0°Cto,60°C | 環(huán)境濕度 | 5至95% |
加工定制 | 否 | 重量 | 3磅 |
MOTOROLA 摩托羅拉 MVME2100
MVME2100 配置設置1-4避免接觸集成電路區(qū)域;靜電放電會損壞這些電路。筆記如果收到時運輸紙箱損壞,請要求承運人的代理人在開箱和檢查期間在場設備器材。從裝運箱中取出設備。參考包裝列出并驗證所有項目是否存在。保存包裝材料設備的儲存和再運輸。產生所需的配置并確保正確操作板,可能需要在之前和之前進行某些修改安裝后。以下段落討論了準備將 MVME2100 硬件組件安裝到機箱之前并將它們連接起來。MVME2100 通過設置提供對大多數選項的軟件控制控制寄存器中的位。在系統中安裝后,您可以修改它的配置。有關電路板控制寄存器的更多信息,請參閱 MVME2100 單板計算機程序員參考附錄中列出的指南但是,有些選項不是軟件可編程的。這些選項是通過手動安裝或移除跳線或額外的MVME2100 上的接口模塊。MVME2100 上手動配置的跳線包括:內存使用(焊接或插接閃存)(J9)系統控制 (J2)Bank A(焊接存儲器)由四個 16 位器件組成,它們分別是裝有 8 Mbit 閃存設備 (4MB)。跳線接頭 J9(引腳 1 和2) 提供 Bank A (Bank 1) 或 Bank B (Bank 0) 之間的選擇配置(僅限 PPCBug 使用)。Bank B 由兩個 32-pin PLCC 8-bit 中的 1MB 8-bit Flash 存儲器組成插座。必須在 A 組的 J9 引腳 1 和 2 之間安裝跳線,或者銀行 B 關閉(出廠默認設置)。
MVME2100 configuration settings 1-4 avoid contacting the integrated circuit area; Electrostatic discharge can damage these circuits. Note if the transport carton is damaged upon receipt, please ask the carrier's agent to be present during unpacking and inspection. Remove the equipment from the shipping box. Refer to the packaging list and verify that all items exist. Store and re transport packaging materials and equipment. Generating the required configuration and ensuring the correct operation of the board may require some modifications before and after installation. The following paragraphs discuss preparing and connecting MVME2100 hardware components to the chassis.
MVME2100 provides software control of most options by setting bits in the control register. After installation in the system, you can modify its configuration. For more inbation about board control registers, refer to the guidelines listed in the MVME2100 board computer programmer's reference appendix. However, some options are not software programmable. These options are achieved by manually installing or removing jumpers or additional interface modules on the MVME2100. The jumper manually configured on MVME2100 includes: memory usage (welding or plug-in flash memory) (J9) system control (J2) bank a (welding memory). It is composed of four 16 bit devices, which are equipped with 8 Mbit flash memory device (4MB). Jumper connector J9 (pins 1 and 2) provides a selective configuration between bank a (bank 1) or bank B (bank 0) (ppcbug use only). Bank B consists of 1MB 8-bit flash memory in two 32-pin PLCC 8-bit sockets. A jumper must be installed between J9 pins 1 and 2 of group A, or bank B is turned off (factory default).
MOTOROLA MCP750
MOTOROLA MVME147-013
MOTOROLA MVME162-012
MOTOROLA MVME162-012
MOTOROLA MVME162-012
MOTOROLA MVME162-023A
MOTOROLA MVME162-10
MOTOROLA MVME162-13
MOTOROLA MVME162-220
MOTOROLA MVME162-512
MOTOROLA MVME162-512A
MOTOROLA MVME162-512A
MOTOROLA MVME162-522A
MOTOROLA MVME162-522A 01-W3960B/61C
MOTOROLA CPCI-6020TM
MOTOROLA MVME162-210
MOTOROLA MVME2301-900
MOTOROLA MVME2604 712I/O
MOTOROLA MVME300
MOTOROLA MVME712/M
MOTOROLA 30-W2960B01A
MOTOROLA FAB 0340-1049