| 詳細參數 | |||
|---|---|---|---|
| 品牌 | PROSOFT | 型號 | MVI46-ADMNET |
| 結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
| LD指令處理器 | 硬PLC | 功能 | 應用開發模塊 |
| 工作電壓 | 5VDC,5% | 輸出頻率 | 1100mA,最大值 |
| 處理速度 | 10Mbit/s,200Datasets/s | 產品認證 | UL |
| 環境溫度 | -40°C至85°C | 環境濕度 | 5%至95%（無冷凝） |
| 加工定制 | 否 | 重量 | 0.35磅 |
| 產地 | 美國 | 外形尺寸 | 5.75x5.25x1.25 |
通過將串行DF1消息從傳統設備轉換并重定向到EtherNet/IP，該模塊為ControlLogix和CompactLogix平臺。當連接到提供多個DF1端口的設備時，可以使用兩個MVI46-ADMNETDF1通信冗余?？梢栽趦煞N模式中的一種進行配置，即同時模式或活動模式/備用物品在同步模式下，兩個模塊將相同的流量路由到相同的Logix控制器。實際上，Logix控制器將收到每條消息中的兩條消息，并且處理這兩個問題。主動/備用模式要求兩種模式都是Logix“所有”。其中一個通過設置禁止路由位，模塊的路由功能被禁用在輸出程序集中。Logix控制器中的邏輯可以監視連接和激活模塊的性能，如有必要，抑制激活模塊和取消禁用備用模塊。
By converting and redirecting serial DF1 messages from legacy devices to EtherNet/IP, the module provides an interface for data exchange to ControlLogix and CompactLogix platbs.When connected to devices that provide more than one DF1 port, it is possible to implement DF1 communication redundancy with the use of two MVI46-ADMNET.These can be configured in one of two modes, either Simultaneous or Active /Standby.
In the Simultaneous mode, both modules route the same traffic to the same Logix controller. Effectively, the Logix controller will receive two of each message and process both of them.Active / Standby mode requires both modes to be Logix “Owned”. One of the modules has its routing capability disabled, achieved by setting the Inhibit Routing bit in the output assembly. Logic in the Logix controller can monitor the connection and perbance of the Active module and, if necessary, inhibit the Active module and un-inhibit the Standby module.
其他型號：
MVI69-MNET
MVI69-MNETC
MVI69-HART
MVI69-AFC
MVI69-DFCM
MVI69-GSC
MVI69-MCM
MVI69-PDPMV1
MVI69-PDPS
PS69-DPS
MVI56-ADM
MVI56-ADMNET
MVI56-MNET
MVI56-MNETC
MVI56-MNETCR
MVI56-MNETR
MVI56-HART
MVI56-AFC
MVI56-DFCM
MVI56-DFCMR
MVI56-DH485
MVI56-GSC
MVI56-MCM
MVI56E-MCM
MVI56E-MNET
MVI56E-MCMR
